Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Our tumblers finish plated hardware for period style hardware. Plated hardware shipped from Upland get the right media for the metal, a careful rinse and dry, and a check for stuck media before they're packed and sent back.
What happens to plated hardware inside our tumblers
Every job starts with a written quote based on your photos and part count. It's free, there's no obligation, and you get a quote number to put on the box. That number ties the shipment to your order when it reaches Oceanside from Upland, Rancho Cucamonga or anywhere else.
If we think a sample run will help, we'll say so up front. If we think tumbling rounds your edges more than you'd like, we'll say that too. The point is to settle the details before the plated hardware are in the drum.
Standard turnaround is 3 to 5 weeks, and expedited orders of 5 to 7 business days are possible depending on availability. Tell us about any deadline when you ask for the quote from Upland.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Pick one finish or combine a few. We often smooth first, then burnish or age the piece, and we plan the steps around the plated hardware you ship from Upland.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
You don't have to live nearby to work with us.
Customers all over the country pack their parts and ship them to our Oceanside shop. We finish them, inspect them and send them back insured. It starts with a few photos.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Six steps take your plated hardware from a box in Upland to a finished batch coming back to your door.
Tell us what the parts are, how many you have and the finish you are after.
Plated hardware are heavy for their size, so use a strong box and fill the empty space. Bag plated hardware by part number, insure the box and ship it after your quote number comes through.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
From hardware to production parts, the work we do falls into a few groups, and plated hardware fit in more than one. See where your plated hardware belong.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Good batches of plated hardware start before the box is sealed
Samples are the best way to avoid surprises with plated hardware. If you can include one or two extra pieces in the box from Upland, we can use them to test a tumbled antique finish before the full batch of plated hardware runs.
If you already have a piece with the look you want, send that along with the plated hardware. Matching a finish by eye is easy when we can hold the real thing next to your plated hardware in the drum, and it keeps everyone on the same page.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Shipping plated hardware to us from Upland is easy once you know the steps. Follow these four and your plated hardware will arrive ready to run.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Upland is at the foot of the San Gabriel Mountains in San Bernardino County. That puts us a good distance apart, which is why we handle tumbling by mail and keep every step in writing, from the quote for your plated hardware to the return shipment.
Close to Claremont or Upland? The nearby pages below follow the same simple process, whether you're near Rancho Cucamonga or Claremont.
Frequently Asked Questions
Thinking about sending plated hardware? These answers cover the basics, from packing to a tumbled antique finish, for plated hardware shipped from Upland.
Start by emailing photos of your plated hardware, the metal type and a part count. We send a written quote and a quote number for your plated hardware. Then bag each part number of plated hardware, pack a strong box, insure it and ship it to Oceanside, with the tracking number emailed to us.
Tumbling removes very little metal from plated hardware, but it does round corners. If your plated hardware have tight tolerances or edges that must stay sharp, tell us before we quote and we'll plan around it. We can run a sample of your plated hardware first so you can measure a finished piece.
Yes, lightly. A short tumble over plated or darkened parts wears the high points through and gives plated hardware an antique, lived in look. Too much time cuts through the finish, so we review jobs with plated hardware first and usually run a sample.
It often does. Tumbling takes off burrs, rounds sharp edges and gives an even surface, which suits parts going to period style hardware. Tell us about the application and any tight fits on the plated hardware, and we'll plan the media and cycle around it.
Yes. We pick the media and cycle time for the metal, run a sample of your plated hardware so you can approve the result, and then finish the full batch. If you have a piece with the look you want, send it or a photo and we'll match it as closely as we can on your plated hardware.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.