Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Our tumblers finish aluminum brackets and housings for enclosures and assemblies. Brackets and housings shipped from Rialto get the right media for the metal, a careful rinse and dry, and a check for stuck media before they're packed and sent back.
Everything aluminum brackets and housings need, under one roof
Plating shows every flaw underneath it. Burrs, scale, light rust and tool marks all end up in the final finish unless they're dealt with first. Tumbling clears most of that away in one pass, which is why many parts from Rialto and Fontana start here before they go anywhere else.
The payoff is a smoother base and sharper looking plating, often for less money than sanding or polishing each piece. Edges get rounded just enough that copper, nickel or chrome covers them evenly.
Because we plate in the same shop, your aluminum brackets and housings don't have to travel to a second vendor. Tell us what finish comes next and we'll plan the tumbling around it. Photos and a part count are all we need to start.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Whatever the metal, we match the finish to the job, from aluminum brackets and housings to anything in between. Brackets and housings sent from Rialto might need burrs removed, edges rounded, a bright burnished shine or a smooth matte surface.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Six steps take your aluminum brackets and housings from a box in Rialto to a finished batch coming back to your door.
Tell us what the parts are, how many you have and the finish you are after.
Send the box of aluminum brackets and housings to our Oceanside address, 2613 Temple Heights Dr, Ste G. Put a sheet inside with your name, phone, email and quote number, and email the tracking number for your brackets and housings as soon as you have it.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Tumbling isn't only for one kind of business, and aluminum brackets and housings are a good example. Here's a look at who uses it and why, whatever the size of your order of brackets and housings.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
A little prep gives aluminum brackets and housings a better finish
Samples are the best way to avoid surprises with aluminum brackets and housings. If you can include one or two extra pieces in the box from Rialto, we can use them to test a smooth matte surface before the full batch of brackets and housings runs.
If you already have a piece with the look you want, send that along with the aluminum brackets and housings. Matching a finish by eye is easy when we can hold the real thing next to your brackets and housings in the drum, and it keeps everyone on the same page.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Shipping aluminum brackets and housings to us from Rialto is easy once you know the steps. Follow these four and your brackets and housings will arrive ready to run.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Wherever you are around Fontana, Colton or Rialto, the process is the same. Rialto is in the Inland Empire of San Bernardino County, so parts travel by mail and come back insured and packed by part number.
More tumble finishing pages for places close to Rialto, including Fontana, are listed here.
Frequently Asked Questions
We like questions about aluminum brackets and housings, because they lead to better finishes. These are good ones to read before you send brackets and housings from Rialto.
Put in a printed sheet with your name, phone number and email, the quote number, part numbers with quantities, the finish you want on the aluminum brackets and housings and any next step like plating. Keep each part number of brackets and housings in its own labeled bag.
Yes. Shops, makers and homeowners anywhere can mail aluminum brackets and housings to us. Brackets and housings from near Fontana, Colton or Rialto follow the same path: photos, a written quote, a sample, then the full batch.
Often, yes. Tumbling removes scale, light rust and surface marks, so copper, nickel or chrome goes on your aluminum brackets and housings smoother and looks better for less cost. It also rounds sharp edges, which helps plating cover the corners of brackets and housings evenly, and we handle both steps in our shop.
Tumbling shines when you have a few dozen aluminum brackets and housings or more, up to full production runs. With a handful of brackets and housings, hand polishing may cost less, and we'll say so honestly once we see your photos and the part count.
Yes, but tell us about them first. Media can wedge into openings close to its own size, so we pick a shape and size that stays clear of the openings on your aluminum brackets and housings. Send the hole sizes of your brackets and housings with your photos, and every finished batch is checked for lodged media.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.