Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Parts shipped from Yucaipa come out of our tumblers deburred, smooth and ready for plating or assembly. We choose the media for each metal, check every batch and pack the parts by part number before they go home insured, with photos of the finished batch when needed.
Small batch or big run, we handle both
Our tumbling work runs from a few dozen pieces up to full production runs. That range is wide on purpose, because not everyone who needs tumbling has a thousand parts, and not everyone has a dozen. Either way, the same care goes into your batch.
A few dozen brass pulls need the same care as a few thousand machined fittings, just in a different drum. And if you only have a handful of pieces, we'll tell you so. Hand polishing can cost less in that case, and we'd rather point you there than take your money for the wrong job.
Send photos and a part count and we'll suggest the best way to go, whether you're in Yucaipa, Redlands or Beaumont. The quote is free and in writing, so you can take your time and compare it with anything else you're considering.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Whatever the metal, we match the finish to the job. Parts shipped from Yucaipa might need burrs removed, edges rounded, a bright burnished shine or a soft tumbled look that feels aged.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Six steps take your parts from a box in Yucaipa to a finished batch coming back to your door.
Tell us what the parts are, how many you have and the finish you are after.
Once your quote number arrives, ship your parts from Yucaipa to our receiving dock in Oceanside. A strong box, labeled bags and insurance for the real value will keep everything safe on the road.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Tumbling serves a wide mix of businesses. These are the kinds of work we finish most, and parts from Yucaipa can fit any of them.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Pack it right and we'll do the rest
Photos help more than almost anything else. Take a few clear shots of your parts from Yucaipa in good light, one of the whole group and a couple up close. Add a photo of the finish you'd like if you have an example.
Tell us about the metal, too. Brass, steel and stainless can take stronger media, while aluminum and zinc need a lighter touch. If you aren't sure what your parts are made of, say so and we'll help figure it out.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Small metal parts travel well when they're packed right. Here's how to send a box from Yucaipa to our Oceanside shop.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Yucaipa sits at the edge of the San Bernardino Mountains, well outside our local drop off area, so we handle it all by mail. Send photos, wait for your quote number, then ship the box. Calimesa and Beaumont work the same way.
Nearby cities have their own tumble finishing pages too, listed here.
Frequently Asked Questions
We like questions, because they lead to better finishes. These are good ones to read before you send parts from Yucaipa.
No. Our drop off option is for local shops around Oceanside, Vista, Carlsbad and San Marcos. Everyone else ships, and it works well. You pack the parts, we finish them, and everything comes back insured and packed by part number.
Oceanside is a long drive from Yucaipa, so most people ship. Drop off is mainly meant for local shops around Oceanside, Vista, Carlsbad and San Marcos. Shipping is simple, and your parts come back packed by part number and insured.
Burnishing uses small steel shapes that press the surface smooth instead of cutting it away. The result is a bright, clean shine on brass, copper and steel without buffing each piece by hand, and almost no metal is removed in the process.
Yes. We darken the brass and then tumble it so the high points wear back to bright metal, which looks like decades of use. It's popular on knobs, hinges, pulls and small castings that need to blend in with older pieces.
Often, yes. Tumbling removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and looks better for less cost. It also rounds sharp edges, which helps plating cover corners evenly. We handle both steps in our shop.
The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.
Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.
When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.