Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
We tumble finish small metal parts shipped to us from Yorba Linda, or from anywhere else in the country. Deburring, edge smoothing and burnishing are done by the batch, with a sample first. Send photos and a part count, and we'll send back a free written quote.
From rough castings to smooth, even parts
Castings come out of the mold with parting lines, rough skin and sharp corners. Machined parts come off the mill with burrs and tool marks. Tumbling takes care of both without anyone holding each piece, which is why it's the usual choice for batches, whether they start in Yorba Linda, Placentia or Brea.
At Decorative Metal Coatings we've been finishing metal since 1989, and our tumbling work covers brass, bronze, copper, steel, stainless, aluminum and zinc die cast. Each metal gets its own media and cycle time, and hard metals and soft ones never share a load.
Some parts go straight back to you. Others move on to plating, patina or lacquer in our shop. Either way, we pack everything by part number and ship it back insured, so your parts reach Yorba Linda organized the way you'd want to store them.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Pick one finish or combine a few. We often smooth first, then burnish or age the piece, and we plan the steps around the parts you ship from Yorba Linda.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
You don't have to live nearby to work with us.
Customers all over the country pack their parts and ship them to our Oceanside shop. We finish them, inspect them and send them back insured. It starts with a few photos.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Your parts follow these steps from the moment you ask for a quote in Yorba Linda until they come home.
Tell us what the parts are, how many you have and the finish you are after.
Bag by part number, box it tightly and ship it to our Oceanside shop. Add your quote number to the printed sheet inside, and send us the tracking number so we can watch for it.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Casinos, machine shops, furniture makers and small brands all rely on tumbled metal. Here's who we finish for, and where a shipped batch from Yorba Linda tends to fit in.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Know your parts, know your finish
A little planning goes a long way with tumbling. Before you ship from Yorba Linda, sort your parts by metal and by part number. Brass, steel and aluminum run best in their own loads, so mixing them in one bag only slows things down.
Next, tell us what the parts will be used for and what you expect them to look like. A part that sits in a drawer needs a different finish than one that gets handled all day, and a photo of the look you want is worth a page of description.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Shipping parts to us from Yorba Linda is easy once you know the steps. Follow these four and your parts will arrive ready to run.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Yorba Linda is up in northern Orange County, along the Santa Ana Canyon, and our Oceanside shop is farther down the coast. Parts travel by mail, so there's no freeway time for you. Send photos first, then ship once you have a quote number.
More tumble finishing pages for cities close to Yorba Linda are listed here.
Frequently Asked Questions
Tumbling is easy to start but has a few details worth knowing. Here are answers that should help anyone sending parts from Yorba Linda.
Yes. Our process doesn't change by location, so shipping from Placentia, Brea or Yorba Linda follows the same steps: photos, a quote number, labeled bags, a strong insured box and a tracking number sent by email.
We dry steel quickly after tumbling so it doesn't flash rust, and we pack finished parts dry for the ride home. If you want extra protection, ask about a clear lacquer or the next plating step before the parts ship back.
We use several types and choose by metal. Ceramic cuts fast on hard metals, plastic is gentler on brass, aluminum and zinc, porcelain leaves a fine smooth surface, and stainless steel shapes burnish. Walnut shell and corn cob handle dry finishing and drying.
Wet steel can flash rust quickly, so we rinse it and dry it right away, spot free. Parts are checked before packing, and if you plan to plate, the next step follows soon after. Ask us about clear lacquer if the parts will stay bare.
Yes, lightly. A short tumble over plated or darkened parts wears the high points through and gives hardware an antique, lived in look. Too much time cuts through the finish, so we review these jobs first and usually run a sample.
Not at all. Most of what comes through our door is home and business hardware: faucets, light fixtures, door handles, cabinet pulls, railings and decorative pieces. We also work for hotels, restaurants, boat owners and manufacturers.
Tell us what the part is, roughly how big it is, how many pieces you have and the finish you're after. If you know the metal, mention it. If not, that's fine. We can usually tell from the photos.
Every part is quoted on its own. The biggest factors are condition, the base metal, size and shape, the finish you choose and how many pieces you send. A part with deep pits or broken spots takes more work before it can be plated.