Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
We tumble finish buckles, tags and small goods shipped to us from Seal Beach, from a few dozen pieces up to production runs. Every batch is finished for a bright burnished shine, and we run a sample before the full load so there are no surprises.
Small shop, steady hands, and plenty of buckles, tags and small goods
Plating shows every flaw underneath it. Burrs, scale, light rust and tool marks all end up in the final finish unless they're dealt with first. Tumbling clears most of that away in one pass, which is why many parts from Seal Beach and Long Beach start here before they go anywhere else.
The payoff is a smoother base and sharper looking plating, often for less money than sanding or polishing each piece. Edges get rounded just enough that copper, nickel or chrome covers them evenly.
Because we plate in the same shop, your buckles, tags and small goods don't have to travel to a second vendor. Tell us what finish comes next and we'll plan the tumbling around it. Photos and a part count are all we need to start.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Tumbling does more than one job. For buckles, tags and small goods it can clean, smooth, brighten or age the metal, and we pick the treatment that gets you a bright burnished shine.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Over three decades of plating, one shop in Oceanside.
Every part is stripped, prepped, plated and inspected in our own building, and our work comes with a 12 month workmanship guarantee. Send photos and we'll take it from there.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Think of it as a short checklist: six steps from your first photo in Seal Beach to buckles, tags and small goods back in your hands.
Tell us what the parts are, how many you have and the finish you are after.
Send the box of buckles, tags and small goods to our Oceanside address, 2613 Temple Heights Dr, Ste G. Put a sheet inside with your name, phone, email and quote number, and email the tracking number for your buckles and tags as soon as you have it.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Tumbling isn't only for one kind of business, and buckles, tags and small goods are a good example. Here's a look at who uses it and why, whatever the size of your order of buckles and tags.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Think it through, then send the buckles, tags and small goods over
Group by size if you can. A batch of buckles, tags and small goods that are close in size and weight tumbles evenly, while mixed sizes can finish unevenly. Tell us if your box of buckles and tags holds more than one size so we can plan separate loads.
And think about how many buckles, tags and small goods you really have. A few dozen buckles and tags is a fine place to start, and hundreds or thousands work too. For a handful of buckles and tags, we'll let you know honestly if hand polishing is a better value.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Getting buckles, tags and small goods from Seal Beach to Oceanside takes four steps. None of them are hard, but each one saves time later with buckles and tags.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
You don't need to be nearby for batch work on buckles, tags and small goods. Seal Beach, on the coast at the Los Angeles and Orange County line, works the same as Huntington Beach or Los Alamitos: photos, a quote, a labeled strong box and insurance for the full value.
More tumble finishing pages for places close to Seal Beach, including Long Beach, are listed here.
Frequently Asked Questions
We like questions about buckles, tags and small goods, because they lead to better finishes. These are good ones to read before you send buckles and tags from Seal Beach.
No. Drop off is available at our Oceanside shop if you call ahead, and customers near Long Beach can ship by mail instead. Shipping works well. You pack the buckles, tags and small goods, we finish them, and everything comes back insured and packed by part number.
A little. With salt air off the Pacific, finished brass and steel can dull or spot if they stay bare for a long time. We can add a clear lacquer to your buckles, tags and small goods after tumbling, and we dry every batch completely before it ships back.
It often does. Tumbling takes off burrs, rounds sharp edges and gives an even surface, which suits parts going to makers and small brands. Tell us about the application and any tight fits on the buckles, tags and small goods, and we'll plan the media and cycle around it.
Yes. We pick the media and cycle time for the metal, run a sample of your buckles, tags and small goods so you can approve the result, and then finish the full batch. If you have a piece with the look you want, send it or a photo and we'll match it as closely as we can on your buckles and tags.
The popular ones for buckles, tags and small goods are satin tumbled, bright burnished, soft matte and aged tumbled brass. We also do tumbled antique over plating, worn edge highlights and tumbled and lacquered finishes on buckles and tags. Send an example of the look you want on your buckles and tags and we'll match it as closely as we can.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.