Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Decorative Metal Coatings has finished metal in Oceanside since 1989, and tumbling stainless steel fittings is part of the week. Ship from Santa Ana, get a written quote first, and we'll run a sample so you can see an even satin surface on your own stainless fittings.
Everything stainless steel fittings need, under one roof
Decorative Metal Coatings has been finishing metal in Oceanside since 1989, and tumbling is part of our regular week. You don't have to live close to use us. Parts from Santa Ana, Tustin or Costa Mesa follow the same simple path: you send photos, we quote, you ship, and we send everything back finished.
Tumbling is how we take burrs off machined parts, soften sharp edges and give brass or steel an even look across a whole batch. A drum full of media does the work at once, so every piece gets the same treatment and you don't pay for hand work on each one.
We also plate and patina in the same building. That matters if your Santa Ana parts need copper, nickel or chrome after tumbling, because nothing has to travel to a second shop in between. Send a few photos and a part count and we'll tell you what we would do.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Every batch starts with the same question: what should your stainless steel fittings feel and look like when they're done? For stainless fittings, these are the finishes we can give you.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
You don't have to live nearby to work with us.
Customers all over the country pack their parts and ship them to our Oceanside shop. We finish them, inspect them and send them back insured. It starts with a few photos.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Nothing about the process is complicated. Here's the path your stainless steel fittings take, start to finish.
Tell us what the parts are, how many you have and the finish you are after.
Wrap anything fragile, fill the gaps around your stainless steel fittings and seal the box well. Your stainless fittings travel to Oceanside insured, and we need the tracking number by email as soon as it's on its way.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Tumbling serves a wide mix of businesses. These are the kinds of work we finish most, and stainless steel fittings from Santa Ana can fit any of them.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
A little prep gives stainless steel fittings a better finish
Decide what happens after tumbling. Stainless steel fittings that are going to plating, patina or lacquer from Santa Ana are finished differently than parts that go straight into equipment and fixtures, and each path changes the media we choose.
Tell us the next step for your stainless steel fittings and we'll plan around it. If plating is next, we can do that in our shop too, so your stainless fittings travel to us once and come home done.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Distance is the only thing that changes between Santa Ana and Tustin. The four steps below stay exactly the same for stainless steel fittings.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
With mild coastal weather around Santa Ana, we pack finished parts dry and well protected for the trip home. Santa Ana is in the center of Orange County, far from our Oceanside shop, so everything moves by mail from photos to insured return.
If you're closer to Tustin than Santa Ana, one of these nearby pages may fit better.
Frequently Asked Questions
Here are straight answers to the questions people ask before sending stainless steel fittings from Santa Ana. Don't see yours? Call us or send a message.
Put in a printed sheet with your name, phone number and email, the quote number, part numbers with quantities, the finish you want on the stainless steel fittings and any next step like plating. Keep each part number of stainless fittings in its own labeled bag.
We dry steel quickly after tumbling so it doesn't flash rust, and we pack finished stainless steel fittings dry for the ride home. With mild coastal weather around Santa Ana, ask about a clear lacquer or the next plating step before the parts ship back.
Yes. Hard and soft parts never share a load, and each part number of stainless steel fittings is run, bagged and labeled on its own. When the batch is done, your stainless fittings are packed by part number and shipped back insured.
Yes, when the media fits the metal. Soft metals like aluminum, zinc and brass run with lighter media and shorter cycles so details and dimensions on stainless steel fittings are protected. We keep hard and soft parts in separate loads, because heavy pieces can ding and scratch softer stainless fittings.
Wet steel can flash rust quickly, so we rinse stainless steel fittings and dry them right away, spot free. Your stainless fittings are checked before packing, and if plating is next, that step follows soon after. Ask us about clear lacquer if the stainless fittings will stay bare.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.