Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Tumbling is how we give brass hinges and pulls a soft satin glow without hand work on every piece. Everything comes to us from San Juan Capistrano by mail, and a free written quote for your hinges and pulls needs only photos and a part count.
A careful finish for brass hinges and pulls, one batch at a time
New brass can look a little too shiny for an old house. A soft tumbled finish takes the edge off. Corners round over, the surface turns satin, and the piece looks like it has been handled for years. We do this for hinges, pulls, knobs and small castings.
If you're matching hardware that's already installed, send a photo or a sample piece. We'll aim for the same warm, aged look so new pieces sit right beside the old ones. Shipping from San Juan Capistrano, Dana Point or San Clemente makes no difference to how we work.
Some jobs add a light darkening before tumbling, so the high spots wear through to bright metal and the low spots stay deep. Ask us about it when you send photos from San Juan Capistrano.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Brass hinges and pulls shipped from San Juan Capistrano don't all need the same thing. Some need burrs gone, some need a soft satin glow, and some are heading for cabinet and door hardware next. Tell us which one fits your hinges and pulls.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Wherever you are, from San Juan Capistrano to San Clemente, a batch of brass hinges and pulls moves through the same six steps.
Tell us what the parts are, how many you have and the finish you are after.
Bag by part number, box your brass hinges and pulls tightly and ship them to our Oceanside shop. Add your quote number to the printed sheet inside, and send us the tracking number so we can watch for your hinges and pulls.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Different industries ask tumbling for different things. Here's who we work with, and what they usually want from brass hinges and pulls like yours.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Know your brass hinges and pulls, know your finish
Keep different parts apart. Each part number of your brass hinges and pulls should have its own bag and its own label, because mixing sizes and metals in one bag slows sorting and can scratch softer pieces on the way to us.
Add a printed sheet to the box of brass hinges and pulls with your name, phone, email, quote number and part numbers. It keeps the order straight when it reaches Oceanside, and it saves a phone call later if a question comes up about a soft satin glow.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
You can ship from any state, and San Juan Capistrano and Dana Point are no different. Four simple steps keep your brass hinges and pulls safe on the way to us.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Wherever you are around Dana Point, San Clemente or San Juan Capistrano, the process is the same. San Juan Capistrano is in south Orange County near the old Mission, so parts travel by mail and come back insured and packed by part number.
Parts from Dana Point and San Clemente reach us the same way, and the nearby pages below cover more places like San Juan Capistrano.
Frequently Asked Questions
Tumbling is easy to start but has a few details worth knowing about brass hinges and pulls. Here are answers that should help anyone sending hinges and pulls from San Juan Capistrano.
No. Drop off is available at our Oceanside shop if you call ahead, and customers near Dana Point can ship by mail instead. Shipping works well. You pack the brass hinges and pulls, we finish them, and everything comes back insured and packed by part number.
Yes. Shops, makers and homeowners anywhere can mail brass hinges and pulls to us. Hinges and pulls from near Dana Point, San Clemente or San Juan Capistrano follow the same path: photos, a written quote, a sample, then the full batch.
Burnishing uses small steel shapes that press brass hinges and pulls smooth instead of cutting the surface away. On hinges and pulls the result is a bright, clean shine without buffing each piece by hand, and almost no metal is removed in the process.
Yes, lightly. A short tumble over plated or darkened parts wears the high points through and gives brass hinges and pulls an antique, lived in look. Too much time cuts through the finish, so we review jobs with hinges and pulls first and usually run a sample.
It often does. Tumbling takes off burrs, rounds sharp edges and gives an even surface, which suits parts going to cabinet and door hardware. Tell us about the application and any tight fits on the brass hinges and pulls, and we'll plan the media and cycle around it.
Not at all. Most of what comes through our door is home and business hardware: faucets, light fixtures, door handles, cabinet pulls, railings and decorative pieces. We also work for hotels, restaurants, boat owners and manufacturers.
Tell us what the part is, roughly how big it is, how many pieces you have and the finish you're after. If you know the metal, mention it. If not, that's fine. We can usually tell from the photos.
Every part is quoted on its own. The biggest factors are condition, the base metal, size and shape, the finish you choose and how many pieces you send. A part with deep pits or broken spots takes more work before it can be plated.