Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Burrs and rough edges on small bronze and copper castings don't have to stay that way. Our Oceanside shop smooths them by the batch, and bronze and copper castings from Riverside reach us by mail after a free written quote.
Finishing metal since 1989, with small bronze and copper castings in mind
The same tumbler can make a part look soft and satin, bright and polished, or old and worn in. It depends on the media, the compound and how long the small bronze and copper castings run. When your bronze and copper castings are headed from Riverside to Oceanside, tell us which look you're after.
Satin tumbled is quiet and even. Bright burnished catches the light. Soft matte hides fingerprints. Aged tumbled brass looks like it has been in use for decades. Photos of examples you like help more than any description.
We'll run a sample so you can see the look on your own parts before the full batch, whether you ship from Riverside, Corona or Jurupa Valley. If it's close but not quite right, we adjust and run it again.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Tumbling does more than one job. For small bronze and copper castings it can clean, smooth, brighten or age the metal, and we pick the treatment that gets you a warm, even tone.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
You don't have to live nearby to work with us.
Customers all over the country pack their parts and ship them to our Oceanside shop. We finish them, inspect them and send them back insured. It starts with a few photos.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Here's what happens from the first photo of your small bronze and copper castings to the day the finished parts ship back to Riverside.
Tell us what the parts are, how many you have and the finish you are after.
Bag by part number, box your small bronze and copper castings tightly and ship them to our Oceanside shop. Add your quote number to the printed sheet inside, and send us the tracking number so we can watch for your bronze and copper castings.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Different industries ask tumbling for different things. Here's who we work with, and what they usually want from small bronze and copper castings like yours.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
A few details now save time on your small bronze and copper castings later
Think about condition before you pack. Small bronze and copper castings that are oily, painted or heavily rusted can still be tumbled, but we need to know ahead of time. Cutting oil comes off in the tumbler, while thick coatings on bronze and copper castings might need another step first.
It also helps to know where the small bronze and copper castings go next. Anything headed for plating from Riverside gets a smoother, brighter surface than something meant to stay bare, and we plan the media and cycle time around a warm, even tone.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
From quote to return shipping, here's the whole mail in process for small bronze and copper castings leaving Riverside. It only takes a few minutes to get your bronze and copper castings ready.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
With hot, dry summers around Riverside, we pack finished parts dry and well protected for the trip home. Riverside is in the Inland Empire along the Santa Ana River, far from our Oceanside shop, so everything moves by mail from photos to insured return.
Parts from Corona and Moreno Valley reach us the same way, and the nearby pages below cover more places like Riverside.
Frequently Asked Questions
Tumbling is easy to start but has a few details worth knowing about small bronze and copper castings. Here are answers that should help anyone sending bronze and copper castings from Riverside.
Yes. Ask for a quote first with photos of your small bronze and copper castings and a part count, and wait for your quote number before you ship. It lets us match the box to your order and plan the finish for your bronze and copper castings ahead of time.
We dry steel quickly after tumbling so it doesn't flash rust, and we pack finished small bronze and copper castings dry for the ride home. With hot, dry summers around Riverside, ask about a clear lacquer or the next plating step before the parts ship back.
It often does. Tumbling takes off burrs, rounds sharp edges and gives an even surface, which suits parts going to decor and restoration work. Tell us about the application and any tight fits on the small bronze and copper castings, and we'll plan the media and cycle around it.
Yes. We pick the media and cycle time for the metal, run a sample of your small bronze and copper castings so you can approve the result, and then finish the full batch. If you have a piece with the look you want, send it or a photo and we'll match it as closely as we can on your bronze and copper castings.
The popular ones for small bronze and copper castings are satin tumbled, bright burnished, soft matte and aged tumbled brass. We also do tumbled antique over plating, worn edge highlights and tumbled and lacquered finishes on bronze and copper castings. Send an example of the look you want on your bronze and copper castings and we'll match it as closely as we can.
Not at all. Most of what comes through our door is home and business hardware: faucets, light fixtures, door handles, cabinet pulls, railings and decorative pieces. We also work for hotels, restaurants, boat owners and manufacturers.
Tell us what the part is, roughly how big it is, how many pieces you have and the finish you're after. If you know the metal, mention it. If not, that's fine. We can usually tell from the photos.
Every part is quoted on its own. The biggest factors are condition, the base metal, size and shape, the finish you choose and how many pieces you send. A part with deep pits or broken spots takes more work before it can be plated.