Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
A box of plated hardware from San Jacinto is a good fit for tumbling. We smooth the edges, bring up an even finish and send everything back insured, packed by part number and ready for period style hardware.
Plated hardware deserve a careful finish
Castings come out of the mold with parting lines, rough skin and sharp corners. Machined parts come off the mill with burrs and tool marks. Tumbling takes care of both without anyone holding each piece, which is why it's the usual choice for batches, whether they start in San Jacinto, Hemet or Perris.
At Decorative Metal Coatings we've been finishing metal since 1989, and our tumbling work covers brass, bronze, copper, steel, stainless, aluminum and zinc die cast. Each metal gets its own media and cycle time, and hard metals and soft ones never share a load.
Some parts go straight back to you. Others move on to plating, patina or lacquer in our shop. Either way, we pack everything by part number and ship it back insured, so your plated hardware reach San Jacinto organized the way you'd want to store them.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
From plain deburring to a worn antique look, these are the finishes we offer on plated hardware sent in from San Jacinto. Many batches of plated hardware use more than one, in stages.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
From first message to finished box, this is how a batch of plated hardware moves through our shop.
Tell us what the parts are, how many you have and the finish you are after.
Send the box of plated hardware to our Oceanside address, 2613 Temple Heights Dr, Ste G. Put a sheet inside with your name, phone, email and quote number, and email the tracking number for your plated hardware as soon as you have it.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Tumbling isn't only for one kind of business, and plated hardware are a good example. Here's a look at who uses it and why, whatever the size of your order of plated hardware.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Help us help you, tell us about the plated hardware
A little planning goes a long way with tumbling plated hardware. Before you ship from San Jacinto, sort your plated hardware by metal and by part number. Brass, steel and aluminum run best in their own loads, so mixing your plated hardware in one bag only slows things down.
Next, tell us what the plated hardware are for and what you expect them to look like. Plated hardware headed for period style hardware need a different finish than parts left bare, and a photo of the look you want is worth a page of description.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Here's a plain walkthrough for mailing plated hardware from San Jacinto. Take your time with it, since a well packed box of plated hardware is half the job.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Parts leave San Jacinto, in the San Jacinto Valley of western Riverside County, in a strong box and come home packed by part number. Hemet, Perris and Moreno Valley all use the same steps, so you can follow the same checklist wherever you are.
More tumble finishing pages for places close to San Jacinto, including Hemet, are listed here.
Frequently Asked Questions
We like questions about plated hardware, because they lead to better finishes. These are good ones to read before you send plated hardware from San Jacinto.
Yes. Ask for a quote first with photos of your plated hardware and a part count, and wait for your quote number before you ship. It lets us match the box to your order and plan the finish for your plated hardware ahead of time.
Yes. Deburring production parts like plated hardware is one of the main jobs for tumbling. We run plated hardware by the batch, choose media that stays clear of holes and threads, and check every load for stuck media before packing.
The popular ones for plated hardware are satin tumbled, bright burnished, soft matte and aged tumbled brass. We also do tumbled antique over plating, worn edge highlights and tumbled and lacquered finishes on plated hardware. Send an example of the look you want on your plated hardware and we'll match it as closely as we can.
Tumbling finishes many pieces at once and gives the same result on every one, so cost per part of plated hardware drops as quantity goes up. Hand polishing can bring a true mirror shine to flat faces and keeps edges sharp, but each piece is handled one at a time, which adds up fast on plated hardware. For plated hardware, we'll suggest the better fit after seeing your photos.
Often, yes. Tumbling removes scale, light rust and surface marks, so copper, nickel or chrome goes on your plated hardware smoother and looks better for less cost. It also rounds sharp edges, which helps plating cover the corners of plated hardware evenly, and we handle both steps in our shop.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.