Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Wheels, hubs, hawse pipes and deck rings get stripped down to clean metal here, then rebuilt with copper, nickel and chrome. The result is a hard, bright finish made to stand up to a boat's daily life. Rancho Santa Fe is close enough to bring your hardware to our Oceanside shop yourself, and shipping works well too if you would rather not drive.
More than a shiny coat, it is a rebuilt surface
Some boats are weekend toys and some are family heirlooms. Either way, the hardware on them deserves proper care. We restore cleats, chocks, wheels, rail fittings and cabin hardware for boat owners across Southern California and well beyond, and the process works the same for owners in Rancho Santa Fe and Del Mar.
You send photos and a few notes about where each piece sits on the boat, and we send a written quote. Once the work is done, we send photos for your approval before the parts are packed and shipped home.
From Rancho Santa Fe you can drop the hardware off in person, and neighbors in Del Mar and Encinitas can do the same or ship by ground.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Cleats, wheels, rails, latches and more. Here is what we restore for boat owners in Rancho Santa Fe, and the finishes you can choose for each piece.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
A few steps get your hardware from Rancho Santa Fe back on your boat looking new. Here they are in order.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
You can walk the parts in at our Oceanside shop or send them from Rancho Santa Fe by ground. Wrap each piece on its own so nothing scratches on the way.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Our marine work reaches charter boats, sportfishing boats, classic restorations and resort fixtures. If you are in Rancho Santa Fe and have hardware that needs saving, we can help.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
Easy upkeep helps your chrome last season after season
The easiest way to protect restored hardware is to treat it like the rest of the boat. Rinse it, dry it and give it a little attention now and then, and the finish will repay you. If your boat sits at a coastal harbor, salt air is the main thing to rinse off, and sprinkler spray at home can leave spots too.
Handle restored pieces gently when you reinstall them. Soft padding under tools and gentle tightening keep the new plating free of scratches.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
Close to our shop, or sending by mail, these steps cover the box and the paperwork.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Rancho Santa Fe is known for large estates and ranches, and the harbors along the San Diego coast are not far away. Business hours are Monday to Friday 8:00 AM to 5:00 PM and Saturday 9:00 AM to 2:00 PM, and parts are received on weekdays from 8:00 AM to 4:00 PM Pacific. Shipping from Rancho Santa Fe works too.
Looking for a nearby city? Here are more places we restore boat and yacht hardware.
Frequently Asked Questions
If you have a question that is not here, call us or send a photo of your parts and we will answer directly.
Yes. Door latches, hinges, pulls, cabin lights and vents are all on our list. Brass and bronze cabin hardware plate evenly, so it is some of the easiest work to bring back.
Look for tiny dark pits, chrome lifting at the edges, rust stains below the base and green crust on bronze. Salt air at the dock and sun at home around Rancho Santa Fe can speed all of these up, so catch them early.
Yes, horns, bells and small trim pieces are part of our marine work. Many older ones are pot metal, which we fill with copper and level by hand before plating.
Yes. Moisture, sun, salt or dirt wear on plating over time, and pits start small. Keeping hardware rinsed, dry and waxed slows the process, and replating fixes it once it has started.
Bronze, brass, stainless steel, pot metal, zinc die cast, steel and more. Aluminum is reviewed case by case. Each metal has its own prep, so we pick the steps that suit your piece.
It depends on the part. Older fixtures and hardware are often better made than what you can buy today, or simply can't be found anymore. Send us photos and we'll give you an honest answer, even if that answer is to buy a new one.
Yes. We work with hotels, casinos, restaurants, architects, contractors and manufacturers, as well as homeowners. For businesses we can plate a whole project to one finish so every piece matches.
Yes. Our shop is at 2613 Temple Heights Dr, Suite G, in Oceanside. Bring your quote number and your parts during business hours, Monday to Friday 8 AM to 5 PM or Saturday 9 AM to 2 PM.