Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Yacht and boat hardware has to look good and survive a lot. Our process of stripping, copper filling, nickel and chrome gives your parts a smooth, mirror finish and a solid base against corrosion. Drop your parts off at our Oceanside shop from Rancho Bernardo, or send them by ground shipping, whichever suits your schedule.
Honest advice first, then the plating
A hawse pipe or a deck cleat is not the sort of thing you can buy again in the same style. Older boats often carry original castings that are no longer made, and a good replating job is the only way to keep them on the boat. We do that work for owners in Rancho Bernardo and beyond.
Our process strips the old finish and fixes what lies under it, including worn grooves and pitted bronze, before we add nickel and chrome. We also tell you plainly if a part is too far gone, so you are not paying to save something that will not last.
Photos are all we need to start. Owners in Rancho Bernardo and Escondido can walk parts into our shop in Oceanside, or send photos first and ship once the quote is approved. Parts coming from Poway or Carmel Mountain Ranch travel the same way, and nothing about the process changes.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Every piece below can be restored in bright chrome, satin chrome or polished nickel. Tell us the look you want, and we will suggest the finish that suits each part and the rest of your boat.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
The whole process is easy to follow, even if your boat is nowhere near Oceanside. Here is how it goes.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
Drop the wrapped parts off at our Oceanside shop from Rancho Bernardo, or ship them by ground if you prefer. Either way, bring or send your quote number with the box.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
We work with restorers and shipwrights who send hardware in batches, as well as individual boat owners. Finishes stay consistent, and each set comes back together to Rancho Bernardo.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
Rinse, wipe and relax, because your chrome will hold up to the water
Good plating gives you a head start, and your habits do the rest. Keep restored pieces clean and dry and they will stay bright far longer. Rancho Bernardo is inland, so hardware faces sun and dust at home and salt air whenever the boat is at the coast.
A once a season check helps. Look over each cleat, rail base and latch for dull patches or tiny spots and clean them right away.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
From Rancho Bernardo you can ship your hardware or drop it off. If you ship, these steps keep everything safe.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Rancho Bernardo has business parks along Interstate 15 filled with technology, defense and manufacturing firms, and the coast is close. Rancho Bernardo is a short drive from our shop, so you can bring parts in person during business hours, or ship them if that is easier. Call ahead for large or heavy pieces.
Close to Rancho Bernardo? These pages cover boat hardware restoration in neighboring cities.
Frequently Asked Questions
Short answers to common questions about restoring boat and yacht hardware, with a few notes for Rancho Bernardo owners.
Copper is soft enough to fill pits and rope grooves, and it can be leveled by hand until the surface is smooth. Nickel and chrome then sit on a clean base instead of following every flaw.
Yes. Owners in Rancho Bernardo, Poway and Escondido can all use the same process: photos, a written quote, careful packing and an insured return shipment. Distance does not change the plating.
Yes. Many owners choose bright chrome for cleats and rails and satin chrome or polished nickel for cabin pieces. Tell us the plan and we will keep each set consistent.
Look for tiny dark pits, chrome lifting at the edges, rust stains below the base and green crust on bronze. Dry heat at home and salt air at the dock around Rancho Bernardo can speed all of these up, so catch them early.
Bright chrome has a mirror shine, while satin chrome has a softer, less reflective look. Polished nickel sits in between with a warmer tone. Photos of your boat help us suggest the best match.
It depends on the part. Older fixtures and hardware are often better made than what you can buy today, or simply can't be found anymore. Send us photos and we'll give you an honest answer, even if that answer is to buy a new one.
Yes. We work with hotels, casinos, restaurants, architects, contractors and manufacturers, as well as homeowners. For businesses we can plate a whole project to one finish so every piece matches.
Yes. Our shop is at 2613 Temple Heights Dr, Suite G, in Oceanside. Bring your quote number and your parts during business hours, Monday to Friday 8 AM to 5 PM or Saturday 9 AM to 2 PM.