Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Boat owners send us the hardware that no polish can save. We have been plating in Oceanside since 1989, and we know what corroded bronze and flaking chrome need before a new finish will stay put. If you are in Poway or a nearby town, you can drop parts off at our Oceanside shop, or ship them to us.
Small parts, big difference on the whole boat
Hardware is rarely the first thing people think about when they restore a boat, but it is often what makes the finished boat look right. New varnish next to dull chrome just looks off. We help boat owners in Poway bring the metal up to the same standard.
Bronze, brass, stainless steel, steel and pot metal all come through our shop. Each one has its own prep, and we pick the right steps for the metal before plating begins. If we are unsure about an alloy, we ask you for a photo or the alloy name before you ship.
If you are in Poway, Rancho Bernardo or Escondido, you can bring parts straight to our Oceanside shop, or ship them if that suits you better.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Bronze, brass, stainless, pot metal and steel parts all come through our shop. These are the boat pieces we restore, each one finished to a hard, bright standard.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
Remove the parts, get a quote, ship, wait and approve. That is the short version, and the steps below fill in the rest.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
From Poway you can bring the box to us in person or ship it. Receiving hours are Monday through Friday, 8:00 AM to 4:00 PM Pacific.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
From wooden runabouts to large yachts, and from casino bar rails to marina fixtures, our process is the same. Poway customers get a written quote before any work begins.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
Simple care is all it takes for your hardware to last season after season
Chrome and nickel are hard, bright metals, but they are not magic. They last longest when they are rinsed after use, wiped dry and washed with mild soap every few weeks. Poway days are warm and dry, and dust settles easily, so wipe hardware gently before washing it.
Rinse any spot where lines rub against hardware. Rope carries grit, and over time grit wears through even a good finish.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
You can ship from Poway instead of driving, and these four steps show how.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Poway is a mostly residential city in the hills above San Diego, with the coast and its harbors a drive away. Stop by our Oceanside shop from Poway any weekday, or send the hardware by ground. Either way, we will review it and send a written quote.
Other cities near Poway that ship parts to our Oceanside shop.
Frequently Asked Questions
These answers cover how we work, what drives the price and how long it takes, with notes for Poway.
There is no flat rate, because cost depends on the size of the piece, the metal, how bad the damage is and the finish you pick. We send a free written quote based on your photos, so you know the price before anything ships to Oceanside.
Bright chrome is the classic mirror finish, satin chrome is softer and polished nickel is warmer. Any of them can work on a boat that sees Mission Bay, San Diego Bay and Oceanside Harbor, so tell us the look you want and we will suggest one.
Most projects take 3 to 5 weeks once your parts arrive. If you are up against a deadline, expedited service of 5 to 7 business days is available as our schedule allows, and your written quote will tell you the lead time.
Usually yes. One quote and one box keeps sets matched and makes it easier to finish pieces together. If you are not sure, tell us what you have and we will help you plan.
Yes, and bronze is some of our favorite work. We clean off the corrosion, fill pits and rope grooves with copper, then add nickel and chrome so the piece comes back bright and smooth.
It depends on the part. Older fixtures and hardware are often better made than what you can buy today, or simply can't be found anymore. Send us photos and we'll give you an honest answer, even if that answer is to buy a new one.
Yes. We work with hotels, casinos, restaurants, architects, contractors and manufacturers, as well as homeowners. For businesses we can plate a whole project to one finish so every piece matches.
Yes. Our shop is at 2613 Temple Heights Dr, Suite G, in Oceanside. Bring your quote number and your parts during business hours, Monday to Friday 8 AM to 5 PM or Saturday 9 AM to 2 PM.