Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
We tumble parts until they are smooth to the touch, and we show you a sample first. Ship from Fort Worth, TX, and get a finished batch back in an insured box.
A Straight Answer on Tumble Finishing
Tumbling removes a small amount of metal and rounds corners, so it does change parts a little. For most work that is exactly the point. But if your parts have tight dimensions or edges that must stay sharp, we want to know before we quote.
Tell us about holes, slots and threads too. Media can wedge into openings close to its size, so we pick a shape and size that stays clear of them and check for stuck media afterward. A few details up front saves everyone time.
A short note with your photos from Fort Worth is all it takes. People sending from Arlington, Weatherford or Burleson can use the same checklist: metal, count, finish, tolerances, hole sizes and what happens next.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Here is what we do in the tumbler. Pick the one that fits your parts, or tell us the result you want and we will suggest the right mix.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
A good result comes from doing the steps in order. Here is how we handle parts sent to Oceanside from Fort Worth.
Tell us what the parts are, how many you have and the finish you are after.
Wait for your quote number, then ship. Keep each part type in its own labeled bag, fill the empty space in the box and insure it for what the parts are really worth.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
The tumbler does not care whether the part is decorative or industrial. What matters is the metal, the count and the look you want, and these are the groups we help.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
What to Tell Us Before You Ship
Think about what the parts will do after tumbling. Parts headed for plating want a different surface than parts that will be lacquered or left bare, and we set the run to match that goal.
Casting skin, parting lines and heavy tool marks need stronger media than a light scuff does. A close up photo of the roughest area tells us what we are dealing with.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Parts do not need to be local to be finished well. The steps below get a box from Fort Worth to Oceanside and back again.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Fort Worth mixes cowboy heritage, a famous Stockyards district and a strong aerospace and manufacturing base. Western hardware, belt buckles and small brass goods fit right in with what our tumblers do. Texas heat is hard on bare metal, so ask us about lacquer.
Nearby cities get the same tumble finishing, sample runs and free quotes as Fort Worth.
Frequently Asked Questions
Questions about finishes, metals, turnaround and shipping are covered below. If something is missing, ask us.
Yes. We tumble a few pieces and show you the result, and the full batch only runs after you approve. It is the best way to avoid surprises.
Yes. Buckles, tags, keychains and similar small goods finish well in batches, and brass takes a lovely satin, bright or aged look. Send photos from Fort Worth and we run a sample first.
Yes. We work on antique hardware, classic car and motorcycle parts and other restoration pieces. Tell us what the part is and what you want, and we will say whether tumbling is the right step.
Yes. Clear lacquer is available, and tumbled and lacquered is one of the finishes we offer. It is a clear coat applied after tumbling to hold the look you chose.
A printed sheet with your name, phone number and email, your quote number, the part numbers and quantity in each bag, and the finish and any next step such as plating.
Not at all. Most of what comes through our door is home and business hardware: faucets, light fixtures, door handles, cabinet pulls, railings and decorative pieces. We also work for hotels, restaurants, boat owners and manufacturers.
Tell us what the part is, roughly how big it is, how many pieces you have and the finish you're after. If you know the metal, mention it. If not, that's fine. We can usually tell from the photos.
Every part is quoted on its own. The biggest factors are condition, the base metal, size and shape, the finish you choose and how many pieces you send. A part with deep pits or broken spots takes more work before it can be plated.