Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
You choose the look, from satin to bright burnished to a soft aged finish. We choose the media to get there and send you a sample first.
Why We Start With a Sample Run
The tumbler is only part of the job. After the run, every batch is rinsed and dried spot free, and then we check the parts for lodged media and any burrs that were missed. Parts with holes and threads get a close look, since media can wedge into small openings.
We also keep different parts apart. Each part number is run and packed separately and labeled the way you sent it, so the box that comes back is ready for your shelf or your assembly line. It sounds like a small thing until you have opened a mixed box.
That level of care applies to a small box from Dallas as much as to a large run from Irving or Plano. If Garland is closer to you, nothing changes, and every batch leaves our shop under our craftsmanship guarantee.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Here is what we do in the tumbler. Pick the one that fits your parts, or tell us the result you want and we will suggest the right mix.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
A good result comes from doing the steps in order. Here is how we handle parts sent to Oceanside from Dallas.
Tell us what the parts are, how many you have and the finish you are after.
When the quote is approved, put your parts in labeled bags and pack them snugly. Insure the box for its real value and email us the tracking number so we can watch for it.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
The tumbler does not care whether the part is decorative or industrial. What matters is the metal, the count and the look you want, and these are the groups we help.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
What to Tell Us Before You Ship
If you are comparing finishes, send photos of each one. Satin, bright burnished and soft matte are close cousins, and a picture helps us work out which one you mean.
Mixed batches take longer to sort and can cost more to run. If you can, send each part type in its own bag with its part number, and tell us which parts get which finish.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Parts do not need to be local to be finished well. The steps below get a box from Dallas to Oceanside and back again.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Dallas is a business hub with a large design and home furnishings trade, and the heat is real from May through September. Decorative hardware, lighting parts and fixtures get a lot of attention here. We can tumble them to match across a full order.
Nearby cities get the same tumble finishing, sample runs and free quotes as Dallas.
Frequently Asked Questions
Questions about finishes, metals, turnaround and shipping are covered below. If something is missing, ask us.
We pack them by part number and ship them back insured. When it helps, we send photos of the sample or the finished batch first.
Yes. Lighting and fixture parts, cabinet hardware and decorative trim finish well in matching batches. Send photos and a count from Dallas, and we recommend a finish and run a sample for approval.
Yes. We offer copper, nickel, chrome and brass plating, plus patinas, and all of it happens in the same building. Tell us what comes next and we tumble to suit it.
Bag each part type separately and label the bag with its part number. Use a strong box, fill the empty space so nothing shifts and insure the box for its real value. Small metal parts are heavy, so sturdy packaging matters.
Describe what the parts are used for and send a photo of a look you like. We will suggest a finish, run a few samples if needed and send back a written quote.
It depends on the part. Older fixtures and hardware are often better made than what you can buy today, or simply can't be found anymore. Send us photos and we'll give you an honest answer, even if that answer is to buy a new one.
Yes. We work with hotels, casinos, restaurants, architects, contractors and manufacturers, as well as homeowners. For businesses we can plate a whole project to one finish so every piece matches.
Yes. Our shop is at 2613 Temple Heights Dr, Suite G, in Oceanside. Bring your quote number and your parts during business hours, Monday to Friday 8 AM to 5 PM or Saturday 9 AM to 2 PM.