Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Tumbling is how we give small bronze and copper castings a warm, even tone without hand work on every piece. Everything comes to us from Valley Center by mail, and a free written quote for your bronze and copper castings needs only photos and a part count.
Small shop, steady hands, and plenty of small bronze and copper castings
The same tumbler can make a part look soft and satin, bright and polished, or old and worn in. It depends on the media, the compound and how long the small bronze and copper castings run. When your bronze and copper castings are headed from Valley Center to Oceanside, tell us which look you're after.
Satin tumbled is quiet and even. Bright burnished catches the light. Soft matte hides fingerprints. Aged tumbled brass looks like it has been in use for decades. Photos of examples you like help more than any description.
We'll run a sample so you can see the look on your own parts before the full batch, whether you ship from Valley Center, Escondido or Bonsall. If it's close but not quite right, we adjust and run it again.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Whatever the metal, we match the finish to the job, from small bronze and copper castings to anything in between. Bronze and copper castings sent from Valley Center might need burrs removed, edges rounded, a bright burnished shine or a warm, even tone.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Wherever you are, from Valley Center to Pauma Valley, a batch of small bronze and copper castings moves through the same six steps.
Tell us what the parts are, how many you have and the finish you are after.
Wrap anything fragile, fill the gaps around your small bronze and copper castings and seal the box well. Your bronze and copper castings travel to Oceanside insured, and we need the tracking number by email as soon as it's on its way.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Tumbling serves a wide mix of businesses. These are the kinds of work we finish most, and small bronze and copper castings from Valley Center can fit any of them.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Think it through, then send the small bronze and copper castings over
Keep different parts apart. Each part number of your small bronze and copper castings should have its own bag and its own label, because mixing sizes and metals in one bag slows sorting and can scratch softer pieces on the way to us.
Add a printed sheet to the box of small bronze and copper castings with your name, phone, email, quote number and part numbers. It keeps the order straight when it reaches Oceanside, and it saves a phone call later if a question comes up about a warm, even tone.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
You can ship from any state, and Valley Center and Escondido are no different. Four simple steps keep your small bronze and copper castings safe on the way to us.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Parts leave Valley Center, in the hills of inland north San Diego County, in a strong box and come home packed by part number. Escondido, Pauma Valley and Bonsall all use the same steps, so you can follow the same checklist wherever you are.
If you're closer to Escondido than Valley Center, one of these nearby pages may fit better.
Frequently Asked Questions
Here are straight answers to the questions people ask before sending small bronze and copper castings from Valley Center. Don't see yours? Call us or send a message.
No. Drop off is available at our Oceanside shop if you call ahead, and customers near Escondido can ship by mail instead. Shipping works well. You pack the small bronze and copper castings, we finish them, and everything comes back insured and packed by part number.
Yes. Deburring production parts like small bronze and copper castings is one of the main jobs for tumbling. We run bronze and copper castings by the batch, choose media that stays clear of holes and threads, and check every load for stuck media before packing.
Often, yes. Tumbling removes scale, light rust and surface marks, so copper, nickel or chrome goes on your small bronze and copper castings smoother and looks better for less cost. It also rounds sharp edges, which helps plating cover the corners of bronze and copper castings evenly, and we handle both steps in our shop.
Tumbling shines when you have a few dozen small bronze and copper castings or more, up to full production runs. With a handful of bronze and copper castings, hand polishing may cost less, and we'll say so honestly once we see your photos and the part count.
Yes, but tell us about them first. Media can wedge into openings close to its own size, so we pick a shape and size that stays clear of the openings on your small bronze and copper castings. Send the hole sizes of your bronze and copper castings with your photos, and every finished batch is checked for lodged media.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.