Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Burrs and rough edges on lighting parts and finials don't have to stay that way. Our Oceanside shop smooths them by the batch, and lighting parts from San Marcos reach us by mail after a free written quote.
Done by people who check every batch of lighting parts and finials
Tumbling isn't right for everything, and we'll say so. A handful of large or delicate pieces is often better done by hand, and we'd rather tell you that than run a batch that doesn't suit the lighting parts and finials. It's one reason you can trust the quote when you write from San Marcos or Escondido.
When tumbling is the right call, it saves real money. Many pieces finish at once, every one gets the same treatment, and the cost per part falls as the count goes up.
Send photos, the metal type and a count from San Marcos. We'll tell you which way we'd go and why, in writing, with no obligation. If a sample run makes sense first, we'll suggest that too.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Here's what we run in our tumblers every week, including lighting parts and finials. Pick the one closest to your lighting parts, and send photos if you're not sure which one fits.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Over three decades of plating, one shop in Oceanside.
Every part is stripped, prepped, plated and inspected in our own building, and our work comes with a 12 month workmanship guarantee. Send photos and we'll take it from there.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Here's what happens from the first photo of your lighting parts and finials to the day the finished parts ship back to San Marcos.
Tell us what the parts are, how many you have and the finish you are after.
Shops in San Marcos can drop lighting parts and finials off at our Oceanside shop, so call ahead first. Get your quote first so we know what to expect, or bag by part number and ship the box insured.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
From hardware to production parts, the work we do falls into a few groups, and lighting parts and finials fit in more than one. See where your lighting parts belong.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Pack lighting parts and finials right and we'll do the rest
Think about condition before you pack. Lighting parts and finials that are oily, painted or heavily rusted can still be tumbled, but we need to know ahead of time. Cutting oil comes off in the tumbler, while thick coatings on lighting parts might need another step first.
It also helps to know where the lighting parts and finials go next. Anything headed for plating from San Marcos gets a smoother, brighter surface than something meant to stay bare, and we plan the media and cycle time around a clean, even finish.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
From quote to return shipping, here's the whole mail in process for lighting parts and finials leaving San Marcos. It only takes a few minutes to get your lighting parts ready.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
San Marcos is in North County San Diego, a short drive from our Oceanside shop, so you can drop parts off if you call ahead, Monday to Friday 8:00 AM to 5:00 PM or Saturday 9:00 AM to 2:00 PM. Prefer to ship? Photos, a quote number and a strong insured box do the job.
Close to Vista or San Marcos? The nearby pages below follow the same simple process, whether you're near Escondido or Vista.
Frequently Asked Questions
Thinking about sending lighting parts and finials? These answers cover the basics, from packing to a clean, even finish, for lighting parts shipped from San Marcos.
Yes. Drop off is available at our shop at 2613 Temple Heights Dr, Ste G, Oceanside, so call ahead first. We're open Monday to Friday 8:00 AM to 5:00 PM and Saturday 9:00 AM to 2:00 PM. Get a quote first so we know what to expect with your lighting parts and finials.
It depends on the count. A few dozen pieces or more of lighting parts and finials is a good fit for tumbling. For just a handful of lighting parts, hand polishing can cost less, and we'll tell you honestly after we see your photos.
Tumbling finishes many pieces at once and gives the same result on every one, so cost per part of lighting parts and finials drops as quantity goes up. Hand polishing can bring a true mirror shine to flat faces and keeps edges sharp, but each piece is handled one at a time, which adds up fast on lighting parts. For lighting parts, we'll suggest the better fit after seeing your photos.
Often, yes. Tumbling removes scale, light rust and surface marks, so copper, nickel or chrome goes on your lighting parts and finials smoother and looks better for less cost. It also rounds sharp edges, which helps plating cover the corners of lighting parts evenly, and we handle both steps in our shop.
Tumbling shines when you have a few dozen lighting parts and finials or more, up to full production runs. With a handful of lighting parts, hand polishing may cost less, and we'll say so honestly once we see your photos and the part count.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.