Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
A box of aluminum brackets and housings from Twentynine Palms is a good fit for tumbling. We smooth the edges, bring up an even finish and send everything back insured, packed by part number and ready for enclosures and assemblies.
Finishing metal since 1989, with aluminum brackets and housings in mind
The look you end up with comes down to the media and the cycle, and both get chosen up front. Ceramic cuts fast, plastic is gentle, porcelain leaves things smooth, and stainless steel pins burnish instead of cut. Our Oceanside shop uses all of them, and we match the choice to your metal.
That's the kind of detail we sort out over email and photos, whether you're in Twentynine Palms, Joshua Tree or Yucca Valley. It doesn't take long, and it saves you from ordering a finish that looks nothing like what you pictured.
After that, the plan is easy: a sample run, your approval, and then the full batch. Standard turnaround is 3 to 5 weeks, and expedited orders of 5 to 7 business days are possible when our schedule allows.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Every batch starts with the same question: what should your aluminum brackets and housings feel and look like when they're done? For brackets and housings, these are the finishes we can give you.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Over three decades of plating, one shop in Oceanside.
Every part is stripped, prepped, plated and inspected in our own building, and our work comes with a 12 month workmanship guarantee. Send photos and we'll take it from there.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
From first message to finished box, this is how a batch of aluminum brackets and housings moves through our shop.
Tell us what the parts are, how many you have and the finish you are after.
Bag by part number, box your aluminum brackets and housings tightly and ship them to our Oceanside shop. Add your quote number to the printed sheet inside, and send us the tracking number so we can watch for your brackets and housings.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Different industries ask tumbling for different things. Here's who we work with, and what they usually want from aluminum brackets and housings like yours.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
A few details now save time on your aluminum brackets and housings later
A little planning goes a long way with tumbling aluminum brackets and housings. Before you ship from Twentynine Palms, sort your brackets and housings by metal and by part number. Brass, steel and aluminum run best in their own loads, so mixing your brackets and housings in one bag only slows things down.
Next, tell us what the aluminum brackets and housings are for and what you expect them to look like. Brackets and housings headed for enclosures and assemblies need a different finish than parts left bare, and a photo of the look you want is worth a page of description.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Here's a plain walkthrough for mailing aluminum brackets and housings from Twentynine Palms. Take your time with it, since a well packed box of brackets and housings is half the job.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
You don't need to be nearby for batch work on aluminum brackets and housings. Twentynine Palms, in the Mojave Desert beside Joshua Tree National Park, works the same as Yucca Valley or Morongo Valley: photos, a quote, a labeled strong box and insurance for the full value.
Parts from Joshua Tree and Yucca Valley reach us the same way, and the nearby pages below cover more places like Twentynine Palms.
Frequently Asked Questions
Tumbling is easy to start but has a few details worth knowing about aluminum brackets and housings. Here are answers that should help anyone sending brackets and housings from Twentynine Palms.
Yes. Ask for a quote first with photos of your aluminum brackets and housings and a part count, and wait for your quote number before you ship. It lets us match the box to your order and plan the finish for your brackets and housings ahead of time.
A little. With intense desert heat and very dry air, finished brass and steel can dull or spot if they stay bare for a long time. We can add a clear lacquer to your aluminum brackets and housings after tumbling, and we dry every batch completely before it ships back.
Yes. Hard and soft parts never share a load, and each part number of aluminum brackets and housings is run, bagged and labeled on its own. When the batch is done, your brackets and housings are packed by part number and shipped back insured.
Yes, when the media fits the metal. Soft metals like aluminum, zinc and brass run with lighter media and shorter cycles so details and dimensions on aluminum brackets and housings are protected. We keep hard and soft parts in separate loads, because heavy pieces can ding and scratch softer brackets and housings.
Wet steel can flash rust quickly, so we rinse aluminum brackets and housings and dry them right away, spot free. Your brackets and housings are checked before packing, and if plating is next, that step follows soon after. Ask us about clear lacquer if the brackets and housings will stay bare.
Not at all. Most of what comes through our door is home and business hardware: faucets, light fixtures, door handles, cabinet pulls, railings and decorative pieces. We also work for hotels, restaurants, boat owners and manufacturers.
Tell us what the part is, roughly how big it is, how many pieces you have and the finish you're after. If you know the metal, mention it. If not, that's fine. We can usually tell from the photos.
Every part is quoted on its own. The biggest factors are condition, the base metal, size and shape, the finish you choose and how many pieces you send. A part with deep pits or broken spots takes more work before it can be plated.