Bright Copper
A deep, mirror polished copper finish for lighting, hardware and decorative pieces, sealed with a clear coat so the color stays rich instead of darkening.
Copper Plating in San Bernardino, CA
Copper plating in San Bernardino for homeowners in the older neighborhoods, businesses along Route 66 and downtown, and the university community up north. Ship us your hardware or lighting, and we'll strip, plate and seal it in copper at our Oceanside shop, then insure it home.
Certified, Approved and Verified
How Copper Plating Works from San Bernardino
The county seat under a natural landmark.
San Bernardino is the seat of the largest county in the lower 48 states. Route 66 runs through on Mount Vernon Avenue, the big Santa Fe depot still stands, and the arrowhead shaped scar on the mountain above the city has been a landmark for centuries. Cal State San Bernardino sits in the north end.
Here's one trip. A brass sconce from a historic home near the downtown theater gets boxed and reaches us by ground. We photograph it, soak off the old lacquer, buff out the dark spots, plate fresh copper, seal it, check it under bright lights and send it back insured, ready to rewire.
Route 66 businesses like the retro look, and copper fits it. Older homes in neighborhoods north of downtown send original hardware. Offices and campus departments send plaques and signs.
Tell us what the part is and what you want it to become. Send a few photos and the base metal if you know it, and we will recommend the right copper process, explain the preparation it needs and send back a written quote.
What We Do
Copper Plating Services
Bright copper gives Route 66 signs a retro shine, antique copper suits older homes and satin copper works for daily hardware. Lacquer or patina finishes it, and when a part is going on to chrome, copper is the smoothing layer underneath.
Satin Copper
A brushed, low glare copper with a soft grain. It hides fingerprints and light wear, a favorite for door hardware, cabinet pulls and interior trim.
Antique Copper
Copper that is darkened and then relieved by hand, so the high points glow while recesses stay deep brown. Ideal for period restorations and rustic designs.
Copper Buff Base
A heavy acid copper layer that is cut and buffed flat before nickel and chrome. It fills pits and polishing marks and is the foundation of every show chrome job.
Copper Strike
A thin first layer that locks onto difficult metals like zinc die cast, steel and brass, giving every layer that follows a solid bond.
Industrial Copper
Functional copper for conductivity, solderability and heat treat masking. Plated to a specified thickness on bus bars, connectors, shafts and gears.
Restoration Results
Before and After
Drag the handle on any photo to see the part as it arrived and as it left the shop in copper.
Before
Vintage Table Lamp
Worn, spotted brass with decades of tarnish. Stripped, polished and plated in bright copper, then sealed with a clear lacquer so the warm color stays put.
BRIGHT COPPER
BRASS
LACQUERED
Before
Antique Door Hardware
A full set of levers, plates and hinges with peeling plating. Stripped, copper plated and hand antiqued so the raised details stand out against darker recesses.
ANTIQUE COPPER
STEEL
SET MATCH
Before
Copper Base for Chrome
Pitted metal with failed chrome. Stripped down, built up in heavy acid copper, then cut and buffed flat to create a perfect base for nickel and chrome.
COPPER BUFF BASE
STEEL
SHOW CHROME PREP
One Piece or a Thousand
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
What We Can Finish
Metals We Copper Plate
Copper bonds to more base metals than almost any other plating, but each one still needs the right cleaning and the right first layer.
Steel
Cleaned and activated, then given a copper strike before the main copper layer. Rusted or pitted steel is stripped and copper filled until the surface is smooth.
Brass and Bronze
Plate beautifully once cleaned. A common way to give brass lighting, hardware and fixtures a true copper color without replacing the part.
Zinc Die Cast and Pot Metal
Porous and reactive, so it needs a gentle copper strike before anything else. Pits are copper filled and hand buffed flat, the slow work most shops avoid.
Aluminum
Receives a zincate pretreatment so copper can bond to a surface that would otherwise oxidize instantly. Used for wheels, housings and decorative castings.
Stainless Steel
Its oxide layer resists bonding, so it gets a nickel strike first. After that it takes copper like any other metal, for a warm look on a durable base.
Copper and Specialty Alloys
Solid copper can be replated to restore its surface, and other alloys are reviewed case by case. Send the alloy or a photo and we will confirm before you ship.
Choosing the Right Copper
Three Ways We Use Copper
The same metal, three different goals. Knowing which one your part needs decides how it is prepared, how thick the copper goes on and how it is finished.
Copper as the Finish
- Bright, satin or antique look
- Sealed with clear lacquer
- Lighting, hardware and decor
- Color matched to a sample
- Judged by appearance
Copper Under Chrome
- Heavy layer, buffed flat
- Fills pits and polishing marks
- Covered by nickel and chrome
- Bumpers, trim and wheels
- Judged by the final chrome
Functional Copper
- Conductivity and solderability
- Heat treat stop off masking
- Plated to a set thickness
- Bus bars, contacts, gears
- Judged by spec and coverage
How It Works
Our Copper Plating Process
Send a few photos and a short description. Our written estimate has no obligation attached.
1
Send Photos
Show us the part and tell us the finish you want: bright, satin, antique or a base for chrome.
2
Get Your Quote
We confirm the base metal and the prep it needs, then send a written quote within 24 business hours.
3
Ship or Drop Off
Older San Bernardino fixtures often have worn lacquer with dark tarnish trapped under it. We strip both, buff the brass or steel clean and smooth it, so the new copper looks even across the whole piece.
4
Strip, Strike and Plate
Old finishes come off, the surface is repaired and polished, then struck and plated in copper.
5
Finish and Seal
Parts are buffed, brushed or antiqued, sealed when needed, inspected and shipped back insured.
Copper Plating Catalog
Copper Finishes and Services
Every copper finish and copper related service we run in house.
Decorative Copper
- Bright Copper
- Polished Copper
- Satin Copper
- Brushed Copper
- Antique Copper
- Oil Rubbed Copper
- Clear Lacquer Topcoat
Underlayer and Industrial
- Copper Buff Base for Chrome
- Acid Copper Leveling Layer
- Copper Strike
- Conductive Copper
- Copper for Soldering
- Heat Treat Stop Off Copper
Base Metals and Prep
- Steel
- Stainless Steel
- Brass and Bronze
- Zinc Die Cast
- Aluminum (Zincate)
- Stripping and Replating
- Masking for Selective Plating
- Custom Sample Match
What Our Clients Say
Trusted by Professionals
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Who We Serve
Who Relies on Our Copper
We plate for homeowners, Route 66 businesses, downtown offices, the university, churches and property managers. Single pieces or large orders.
Casinos and Gaming
Slot machine trim, table rails, bar fixtures and gaming floor accents in bright or antique copper, made to glow under bright lights around the clock. Trusted by casino resorts across North County San Diego.
Lighting and Decor
Pendants, sconces, lamp bases and accessories finished in bright, satin or antique copper.
Architectural Hardware
Door handles, hinges, cabinet pulls and railings given a warm copper finish that matches across a project.
Hospitality
Bar rails, foot rests, tap handles and restaurant fixtures that bring copper warmth to a space.
Electrical Components
Bus bars, terminals and connectors plated for conductivity and easy soldering.
Manufacturing and Heat Treat
Gears, shafts and steel parts selectively copper plated to mask areas during carburizing.
35+
Years of Expertise
Take a Moment to Learn More
About Decorative Metal Coatings
We have been running copper tanks since 1989. Restorers, designers, builders and manufacturers send us parts because the copper work underneath is what makes the finish on top last.
Free Estimates Available
Send a photo of your part and receive a no obligation quote within 24 hours.
Quality Guaranteed
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Ship From Anywhere in the US
A single fixture or a full production run, shipped to us from any state and returned insured.
Fast Turnaround Times
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Our Commitment
Copper Done the Right Way
Copper shows everything. Every scratch left in the base metal and every shortcut in the prep ends up visible in the finish, so we do not take shortcuts.
Proper Strike Layer
Difficult metals get the right first layer before the main copper goes on, so the finish stays bonded and does not peel or blister.
Hand Buffed
Copper is cut and buffed by hand between stages, which is what gives decorative copper its depth and chrome its flawless base.
Color Checked
Finished copper is inspected for even color, gloss and texture, and matched to your sample when you send one.
Packed to Protect
Soft copper scratches easily, so every finished piece is wrapped separately and packed to arrive exactly as it left the shop.
What We Do Differently
- We confirm the base metal before choosing the copper process
- Old plating is stripped instead of covered over
- Decorative copper is sealed so the color lasts
- We send photos when a part needs a decision from you
- Every order is inspected before it is packed
What You May Experience Elsewhere
- Copper plated straight over old, failing finishes
- No strike layer, leading to peeling and blistering
- Unsealed copper that turns brown within weeks
- Polishing marks left visible under the finish
- Little communication once parts are in the shop
Copper Care for San Bernardino Homes and Businesses
Valley heat below the San Bernardino Mountains.
San Bernardino gets hot summers and dry winds off the mountains. Lacquered copper indoors stays bright with dusting and a mild soap wipe. Outdoors, rinse dust off first, then dry.
Bare copper outdoors darkens fast in the heat. For signs you want to read clearly, lacquer keeps the contrast. For a weathered Route 66 look, let it age.
If you prefer a living finish, we can leave the copper unsealed so it develops its own patina over time. That choice works well on rustic lighting, garden pieces and bar tops where the aging is part of the character.
When a lacquered piece starts to show dark spots, the coating has failed somewhere. Bring it back and we can strip the old lacquer, rebuff the copper and seal it again, usually without replating the whole part.
Project Gallery
Copper Plating Gallery
Bright, satin and antique copper on lighting, hardware and hospitality pieces, plus functional copper for electrical and industrial work.
Nationwide Service
Ship Us Your Parts From Anywhere in the US
Remove glass and wiring from lights, wrap each piece and pack the box tight.
01
Quote before you ship
Send photos of every piece and the copper finish you want. You receive a written quote and lead time, usually the same business day. Always wait for a quote number before shipping.
02
Wrap every piece on its own
Wrap each part individually so metal never touches metal, and use at least three inches of padding on every side. Long trim and lighting arms should be double boxed.
03
Insure it and share tracking
Declare the real value with the carrier and email us the tracking number so we can log your parts the day they arrive.
04
Inspected, then shipped back
When the copper work is done we photograph the finished pieces for your approval, then pack them in fresh materials and ship them back insured.
Visit Us
Our Location
Every copper job is stripped, plated, buffed and inspected in our own facility in North County San Diego.
Decorative Metal Coatings
Copper, nickel, chrome and metal finishing in San Diego County since 1989.
- Address 2613 Temple Heights Dr, Ste G, Oceanside, CA 92056
- Phone (760) 746 3378
- Quotes Send photos and get a price
Business Hours
- Monday to Friday 8:00 AM to 5:00 PM
- Saturday 9:00 AM to 2:00 PM
- Sunday Closed
Shipping from San Bernardino
Ground shipments leaving San Bernardino generally arrive at our shop after 1 business day. Everything we return is insured.
Nearby Cities We Serve
Other nearby Inland Empire cities we serve:
Copper Plating Company Serving San Bernardino
Frequently Asked Questions
San Bernardino homeowners and business owners often ask us these questions.
Yes. Metal sign letters, plaques and decorative trim plate well. Bright copper gives a classic retro shine, and antique copper looks like it's been on the road for decades. Send photos and sizes, and we'll explain how to pack them safely.
It ships by ground and is logged and photographed when it arrives. We strip the old finish, buff the metal, plate copper and seal it. After a close inspection under bright lights, it's wrapped carefully and shipped back to you insured.
Yes. Plaques, sign letters, display hardware and conductive lab parts are all things we plate. Send photos or samples, tell us how the pieces will be used and we'll suggest the right finish, thickness and level of protection.
Copper looks great on older homes. Antique copper on hinges, knobs and porch lights suits the age of the house and blends with wood trim. Bright copper works for kitchen accents if you want something fresher alongside the originals.
Heat doesn't destroy lacquer, but sun and heat together wear it over the years. Outdoor pieces in full sun need a refresh sooner than shaded ones. Rinsing off dust and drying the copper helps the clear coat last longer.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.