Mirror Polishing
Our brightest finish. The surface is cut, buffed and colored until it reflects like glass, perfect for lighting, display pieces and decorative hardware.
Dull, scratched or tarnished metal can look right again. We polish it by hand and return it insured to Brea, or you can bring it to our shop.
Family heirlooms deserve a careful hand
Family pieces carry stories, and nobody wants them rubbed flat. When an heirloom comes in from Brea, we polish gently so engraving, stamps and fine detail stay sharp while the tarnish comes off.
Tell us what matters most about the piece. If there is lettering or a maker's mark you want left alone, write it on the sheet that goes in the box. We note it on the job.
Candlesticks, trays and keepsakes can travel from Fullerton, La Habra or anywhere else, packed one by one in soft cloth and returned insured.
Send us a few photos and tell us how the piece is used. We will tell you whether polishing alone will get you there or whether it needs plating, explain what finish makes sense and send back a written quote.
Different metals need different compounds, so brass, stainless, aluminum and copper never share a wheel. That is how surfaces stay clear instead of burned or smeared.
Our brightest finish. The surface is cut, buffed and colored until it reflects like glass, perfect for lighting, display pieces and decorative hardware.
A fine, even grain that softens glare and hides fingerprints. A smart choice for handrails, pulls and levers that get touched all day long.
Deep scratches, light pitting and tool marks are worked out wheel by wheel, so the finished surface is smooth and even instead of wavy.
Tarnish and old lacquer come off, the metal is brought back to its warm color and sealed with a clear coat if you want it to stay that way.
Each metal needs its own compounds. We polish stainless to a crisp shine and aluminum to a bright finish without burning or smearing the surface.
Plating copies the surface under it. We polish parts flat and clean before nickel, chrome or gold so the final finish comes out flawless.
Drag the handle on any photo to see how the piece arrived and how it looked when it left our polishing room.
Before
Dark tarnish, fingerprint stains and old lacquer flaking at the edges. Stripped, polished to a mirror and sealed with a fresh clear coat.
Before
Years of scuffs from shoes and stools. Scratches were cut out and the rail was brought back to a bright, uniform shine along its full length.
Before
Chalky gray oxidation over every surface. Hand polished into the curves and details until the aluminum showed a clean, bright finish again.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
More shine is not always better. The right level depends on how the piece is used, how often it is touched and the look you want.
Each metal has its own hardness, color and quirks. Knowing them is what keeps a polish from turning out wavy, burned or hazy.
Polish up beautifully and take a deep mirror. Old lacquer is stripped first, then the metal is buffed and resealed so the warm color holds.
Soft and quick to scratch, so it is buffed gently with fine compounds. Finished bright for a classic look or left to age naturally.
Hard and tough to cut, but it holds a polish for years. Ideal for rails, kitchen and bar equipment and marine fittings near the coast.
Turns dull and chalky outdoors. We polish it bright and can seal it to slow the oxidation that brings the haze back.
Polishes well but rusts if left bare, so it usually gets plated or coated after polishing. We will explain the options before we start.
Soft castings with a thin skin. Pushing too hard opens pits, so we polish these by hand with light pressure and know when to stop.
Starting with photos and ending with an insured return, here is how the work flows.
Show us the piece, the damage and the look you want: mirror, bright or satin.
We check the metal and the condition, then send a written quote within 24 business hours.
Choose shipping or drop off. Either way, your quote number goes with the piece.
Old lacquer and tarnish come off, then scratches are worked out from coarse to fine wheels.
A final color buff, a full cleaning, an optional clear coat and a close look under bright light.
Sometimes Polishing Is All It Takes
Many customers call asking for plating when their piece only needs a good polish. If the part is solid brass, copper, stainless or aluminum and the damage is on the surface, polishing alone brings it back for less money and keeps the original metal you already like.
Plating is the answer when the color needs to change, when the metal underneath is steel that will rust, or when the old plating has already worn through to a different color. In those cases we still polish first, because a plated finish only looks as good as the surface under it.
Not sure which group your piece falls in? Look at a worn corner or the back side. If the color is the same all the way through, it is probably solid and a polish will do. If you see a different color peeking through, it is plated, and we will talk you through replating.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Every polished finish and restoration service we handle in house.
Polishing wheels have been turning in our shop since 1989. It is the skill every other finish we offer depends on, and the reason homeowners, designers and casino resorts keep sending us their metal.
Send a photo of your piece and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
One heirloom or a full hotel renovation, shipped to us from any state and returned insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Polishing is not only for show pieces. Everyday hardware, rails and fixtures keep our wheels busy, and so do family keepsakes.
Slot machine trim, table rails, bar fixtures and decorative accents polished to shine under bright lights day and night. Casino resorts across North County San Diego trust us with their gaming floors.
Bar rails, foot rests, door push plates and lobby fixtures brought back to a bright, welcoming finish.
Door levers, hinges, knobs and railings polished as a matched set so every room looks consistent.
Chandeliers, sconces, lamp bases and decorative pieces polished by hand, curves and details included.
Stainless cleats, rail fittings and bronze hardware cleaned of salt haze and polished to stand up to coastal air.
Family pieces, candlesticks and collectibles polished carefully so engraving, stamps and fine detail stay sharp.
Fast polishing leaves swirls, waves and rounded edges. We take the time each piece needs so the finish looks right from every angle.
Brass, stainless and aluminum each get their own wheels and compounds, so the surface is never burned, smeared or left hazy.
Every grit is fully removed by the next one before we move on. That is how a polish ends up clear instead of swirly.
Finished pieces are cleaned of all compound and inspected under strong light from several angles before they are approved.
A fresh mirror scratches easily, so each piece is wrapped in soft material and boxed to arrive just as it looked in our shop.
How to Protect Your Fresh Polish
Brea has warm, dry weather most of the year, with Santa Ana winds that blow dust over outdoor hardware. A clear coat on brass and copper is the best way to keep color from darkening, and mild soap and water handles the day to day cleaning.
Keep aluminum sealed and wiped to slow the chalky haze it picks up outdoors. A little attention keeps the brightness going.
Unsealed pieces can be kept bright with a gentle metal polish and a clean microfiber cloth. Rub lightly in the direction of the grain on satin finishes, and use a fresh area of the cloth as it picks up black residue. Abrasive pads and kitchen scrubbers will scratch a mirror finish in seconds.
Near the ocean, salt air speeds everything up. Rinse outdoor hardware with fresh water now and then and dry it. When a piece finally loses its shine, send it back. A repolish is usually quick because the hard cutting work was already done the first time.
Metal Finishing Gallery
A look at recent work from our Oceanside shop: plated hardware, lighting, hospitality and casino pieces, marine fittings and industrial parts.
A little packing care goes a long way. Here is how to send pieces to Oceanside from Brea.
Email photos of each piece, front and back, and the finish you want. You receive a written quote and lead time, usually the same business day. Wait for your quote number before you ship.
Wrap every piece on its own in soft cloth or bubble wrap so nothing rubs together in transit. Pad the box with at least three inches on every side and double box long rails or tubes.
Declare the full value with the carrier and email us the tracking number so we know what is coming and can log it the day it lands.
Once polishing is done we send photos for your approval, then pack your pieces in new materials and return them insured.
Every piece is polished, cleaned and inspected by hand in our own shop in North County San Diego.
Metal polishing, plating and finishing in San Diego County since 1989.
Receiving for carrier deliveries runs Monday through Friday, 8:00 AM to 4:00 PM Pacific. Anything coming from Brea by freight that needs a liftgate should be scheduled with us first.
Looking for another nearby city? These pages cover the same service with the same shop behind them.
Frequently Asked Questions
Look through these answers, then send photos if you are ready for a quote. Questions are welcome at any step.
Yes. Drop off works fine, and the shop is open Monday to Friday 8:00 AM to 5:00 PM and Saturday 9:00 AM to 2:00 PM. Get a quote first so we know what to expect.
We polish antiques carefully so engraving, stamps and fine detail stay sharp. Tell us what matters most and we note it on the job.
Polish holds well on hardware that gets normal handling. Satin finishes hide wear best, and a quick repolish later is easy because the cutting work was done the first time.
One small piece is welcome. A candlestick or a door handle goes through the same careful steps as a big order.
Standard turnaround is 3 to 5 weeks. Expedited orders can run 5 to 7 business days, so ask about availability when you request your quote.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.