Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Replacing old marine hardware can mean a long search or a part that no longer fits. Restoring what you already have is often the better answer, and that is the work we do for boaters in Brea. You never have to leave Brea. Photos go out by email, the box goes out by ground, and it usually arrives in one day.
Chrome That Stays Put, Season After Season
The first things people touch when they step aboard are latches, pulls and hinges. Worn hardware in the cabin spoils a boat that is otherwise in good shape, and we fix that for boat owners in Brea.
Small pieces get the same full treatment as a big cleat. We strip them, repair what needs repair and finish them in chrome, satin chrome or polished nickel. Matching sets stay together in the process.
Cabin hardware is light, so it ships well from Brea, Fullerton or Placentia. Wrap each piece separately, bag its fasteners and mark where it goes before the box leaves.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Pick the finish and we do the rest. These are the types of boat hardware we restore for people in Brea and around the country.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
Here is how restoring boat hardware works, step by step, whether you are in Brea or just down the road from our shop.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
Wrap each piece on its own, insure the box and email us the tracking number. From Brea, ground shipping to Oceanside usually takes one day.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Some customers own one boat and others run a fleet or a resort. Owners in Brea and everywhere else get the same careful process.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
What to Do Once the Parts Are Back on Board
Think of plated hardware the way you think of paint on a hull. It protects well as long as you keep it clean. Owners in Brea with boats on Newport Harbor and Dana Point can keep chrome bright with fresh water, mild soap and a dry towel.
Keep an eye on fasteners as well as fittings. A loose or corroded screw lets water under a cleat or rail base, and that is where trouble starts. Replace them with suitable hardware when you reinstall restored pieces.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
Mailing parts is easier than most people expect. These four steps cover everything for hardware coming from Brea.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Brea is an inland Orange County city, but boats owned here are often kept at harbors on the coast. Salt on the dock and sun on the trailer add up, and a box ships easily to Oceanside.
Looking at hardware pages for towns close to Brea? Here are a few more.
Frequently Asked Questions
Short answers about restoring marine hardware, with a few notes for Brea. For something specific, send a photo and we will reply.
After every trip is best. A rinse with fresh water and a wipe with a soft towel take off salt before it settles into the finish. A marine wax or protectant adds another layer against salt air at the harbors and sun on the trailer.
Where the boat lives does not matter to us. Send the parts from wherever you are, and tell us where each piece sits on the boat. We work from the photos and the notes, and the quote comes back in writing.
Rinse with fresh water after trips, wipe dry and wash with mild soap every few weeks. Add a marine protectant or wax. Keep steel wool and harsh rust removers away from chrome.
Yes. These guide rope and chain, so grooves wear into them over the years. We smooth the grooves, fill any pits with copper and finish the piece in chrome or nickel.
Aluminum needs special pretreatment, so we review it part by part. Send a photo or tell us the alloy name and we will confirm what is possible before you ship anything.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.