Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Our shop has been replating since 1989, and boat and yacht hardware is a big part of what we do. Fullerton owners get a written quote based on photos before anything ships. Fullerton is a one day ground shipment from our shop, and your parts come back insured.
Bright work that holds its shine
People often ask how a shop can fix chrome that has already pitted. The honest answer is that we do not plate over damage. Anything on the surface of a boat part from Fullerton that has started to flake or bubble gets stripped away first.
Then the repair begins. Pits are filled with copper and leveled slowly by hand, because rushing that step shows up later as a dull spot. Nickel and chrome follow, and we finish with a daylight inspection before anything is approved to ship.
Our Oceanside shop has worked this way since 1989. If you are in Fullerton, Brea or Placentia, the process starts with photos and ends with a box that comes back insured and ready to bolt on.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Most of what we restore for boat owners in Fullerton falls into six groups, from deck hardware to cabin trim. Here is a closer look at what we do with each one.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
Each step below happens in this order, and none gets skipped for parts coming from Fullerton or anywhere else.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
Box up your hardware with plenty of padding and ship it to us from Fullerton. Bag the fasteners with each fitting and keep the tracking number handy.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Casino resorts, classic boat owners, yacht crews and marinas all need chrome that holds up. Below is how we help each group, including anyone in Fullerton.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
Habits that help your hardware hold up
A boat kept at a coastal marina sees salt and fog, while a trailer boat parked at home collects dust and sun, and each one needs a different routine. Fresh water and a dry towel will do more for your plating than any expensive product.
Plating that has been done properly can handle everyday use, but chrome is still a thin skin over metal. The goal is to keep water, salt and grit from sitting on it. A few minutes after each outing helps the finish last.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
Parts shipped from Fullerton arrive, get plated and come back, with photos along the way.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Think of Oceanside as one shipping day from Fullerton. Hardware goes out in a regular box and returns insured, sorted by set.
Close to Fullerton, we also restore boat parts for people in:
Frequently Asked Questions
Questions come up before every job, so we collected the common ones. The answers apply to boat owners in Fullerton and everywhere else.
Include your name, phone and email on a printed sheet, your quote number, a list of each fitting with the finish you want, and notes on any pairs or sets that must match.
Yes. Rinse and dry every fitting before you cover the boat, because trapped moisture does quiet damage. When you uncover it, look over each piece. If something looks tired, take photos and send them to us.
We restore finish, not structural strength. Load bearing parts such as shackles or chainplates should be inspected by a rigger before they go back on the boat. If you are unsure whether a piece is structural, send a photo and we will advise.
Yes. We tag sets when they arrive and plate them together where we can, so the finish matches from piece to piece. They go back to you together as well, so pairs and sets stay matched.
It depends on the size of the piece, the metal and how much damage there is. A cleat with pitting and peeling needs more repair work than one that is only dull. Send photos and we will give you a free written price for each piece.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.