Mirror Polishing
Our brightest finish. The surface is cut, buffed and colored until it reflects like glass, perfect for lighting, display pieces and decorative hardware.
From door hardware to lighting and bar rails, we bring metal back to a clean, even shine. Ask for a free written quote from Barstow today.
Scratches, tarnish and old lacquer, gone for good
Metal gets beat up. Scratches, light pitting, tool marks, tarnish and flaking lacquer all show up sooner or later, and we work them out wheel by wheel so the surface ends up smooth and even instead of wavy.
If you have something in Barstow that has seen years of hands, shoes or weather, send a photo. We will tell you whether the damage is on the surface or deep enough to need more metal removed than is safe.
We would rather tell you the truth than polish something into a worse shape. The photo and quote steps are the same from Yermo, Victorville or Barstow, and a request takes only a few minutes.
Send us a few photos and tell us how the piece is used. We will tell you whether polishing alone will get you there or whether it needs plating, explain what finish makes sense and send back a written quote.
Good polishing starts with the right wheel and ends with a close look under bright light. Here is the range of finishes and repairs we offer.
Our brightest finish. The surface is cut, buffed and colored until it reflects like glass, perfect for lighting, display pieces and decorative hardware.
A fine, even grain that softens glare and hides fingerprints. A smart choice for handrails, pulls and levers that get touched all day long.
Deep scratches, light pitting and tool marks are worked out wheel by wheel, so the finished surface is smooth and even instead of wavy.
Tarnish and old lacquer come off, the metal is brought back to its warm color and sealed with a clear coat if you want it to stay that way.
Each metal needs its own compounds. We polish stainless to a crisp shine and aluminum to a bright finish without burning or smearing the surface.
Plating copies the surface under it. We polish parts flat and clean before nickel, chrome or gold so the final finish comes out flawless.
Drag the handle on any photo to see how the piece arrived and how it looked when it left our polishing room.
Before
Dark tarnish, fingerprint stains and old lacquer flaking at the edges. Stripped, polished to a mirror and sealed with a fresh clear coat.
Before
Years of scuffs from shoes and stools. Scratches were cut out and the rail was brought back to a bright, uniform shine along its full length.
Before
Chalky gray oxidation over every surface. Hand polished into the curves and details until the aluminum showed a clean, bright finish again.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
More shine is not always better. The right level depends on how the piece is used, how often it is touched and the look you want.
Each metal has its own hardness, color and quirks. Knowing them is what keeps a polish from turning out wavy, burned or hazy.
Polish up beautifully and take a deep mirror. Old lacquer is stripped first, then the metal is buffed and resealed so the warm color holds.
Soft and quick to scratch, so it is buffed gently with fine compounds. Finished bright for a classic look or left to age naturally.
Hard and tough to cut, but it holds a polish for years. Ideal for rails, kitchen and bar equipment and marine fittings near the coast.
Turns dull and chalky outdoors. We polish it bright and can seal it to slow the oxidation that brings the haze back.
Polishes well but rusts if left bare, so it usually gets plated or coated after polishing. We will explain the options before we start.
Soft castings with a thin skin. Pushing too hard opens pits, so we polish these by hand with light pressure and know when to stop.
Our process is simple, and it works the same whether the piece is a single handle or a full set of hardware.
Show us the piece, the damage and the look you want: mirror, bright or satin.
We check the metal and the condition, then send a written quote within 24 business hours.
Send it by carrier with your quote number inside, or drop it off at our shop during open hours.
Old lacquer and tarnish come off, then scratches are worked out from coarse to fine wheels.
A final color buff, a full cleaning, an optional clear coat and a close look under bright light.
Sometimes Polishing Is All It Takes
Many customers call asking for plating when their piece only needs a good polish. If the part is solid brass, copper, stainless or aluminum and the damage is on the surface, polishing alone brings it back for less money and keeps the original metal you already like.
Plating is the answer when the color needs to change, when the metal underneath is steel that will rust, or when the old plating has already worn through to a different color. In those cases we still polish first, because a plated finish only looks as good as the surface under it.
Not sure which group your piece falls in? Look at a worn corner or the back side. If the color is the same all the way through, it is probably solid and a polish will do. If you see a different color peeking through, it is plated, and we will talk you through replating.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Every polished finish and restoration service we handle in house.
Polishing wheels have been turning in our shop since 1989. It is the skill every other finish we offer depends on, and the reason homeowners, designers and casino resorts keep sending us their metal.
Send a photo of your piece and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
One heirloom or a full hotel renovation, shipped to us from any state and returned insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Hospitality, architecture, lighting, marine and antiques make up much of what we polish. Take a look at each.
Slot machine trim, table rails, bar fixtures and decorative accents polished to shine under bright lights day and night. Casino resorts across North County San Diego trust us with their gaming floors.
Bar rails, foot rests, door push plates and lobby fixtures brought back to a bright, welcoming finish.
Door levers, hinges, knobs and railings polished as a matched set so every room looks consistent.
Chandeliers, sconces, lamp bases and decorative pieces polished by hand, curves and details included.
Stainless cleats, rail fittings and bronze hardware cleaned of salt haze and polished to stand up to coastal air.
Family pieces, candlesticks and collectibles polished carefully so engraving, stamps and fine detail stay sharp.
Fast polishing leaves swirls, waves and rounded edges. We take the time each piece needs so the finish looks right from every angle.
Brass, stainless and aluminum each get their own wheels and compounds, so the surface is never burned, smeared or left hazy.
Every grit is fully removed by the next one before we move on. That is how a polish ends up clear instead of swirly.
Finished pieces are cleaned of all compound and inspected under strong light from several angles before they are approved.
A fresh mirror scratches easily, so each piece is wrapped in soft material and boxed to arrive just as it looked in our shop.
A Little Care Keeps It Looking New
Barstow is high desert along the Mojave, with scorching summers, a steady wind and fine dust that settles on everything outside. Strong sun fades unprotected finishes, so ask about a clear coat on brass and copper and keep aluminum sealed against chalky haze.
Dust often with a dry soft cloth and wash with mild soap only when you need to. Dry the piece afterward so water spots do not set in.
Unsealed pieces can be kept bright with a gentle metal polish and a clean microfiber cloth. Rub lightly in the direction of the grain on satin finishes, and use a fresh area of the cloth as it picks up black residue. Abrasive pads and kitchen scrubbers will scratch a mirror finish in seconds.
Near the ocean, salt air speeds everything up. Rinse outdoor hardware with fresh water now and then and dry it. When a piece finally loses its shine, send it back. A repolish is usually quick because the hard cutting work was already done the first time.
Metal Finishing Gallery
A look at recent work from our Oceanside shop: plated hardware, lighting, hospitality and casino pieces, marine fittings and industrial parts.
You can bring your pieces to Oceanside from Barstow or send them in a box. These steps help either way.
Email photos of each piece, front and back, and the finish you want. You receive a written quote and lead time, usually the same business day. Wait for your quote number before you ship.
Wrap every piece on its own in soft cloth or bubble wrap so nothing rubs together in transit. Pad the box with at least three inches on every side and double box long rails or tubes.
Declare the full value with the carrier and email us the tracking number so we know what is coming and can log it the day it lands.
Once polishing is done we send photos for your approval, then pack your pieces in new materials and return them insured.
Every piece is polished, cleaned and inspected by hand in our own shop in North County San Diego.
Metal polishing, plating and finishing in San Diego County since 1989.
Plenty of pieces get here by carrier, and that works fine from Barstow. If you would rather hand it over, our hours are Monday to Friday 8:00 AM to 5:00 PM and Saturday 9:00 AM to 2:00 PM.
Communities like these can send their metal our way by carrier or in person.
Frequently Asked Questions
We kept these answers brief and practical. Need more detail on your piece? Photos make it easy.
A quick call to (760) 746 3378 is a good idea so your quote number and paperwork are ready when you arrive.
Yes. Chandeliers, sconces, lamp bases and decorative pieces are polished by hand, curves and details included.
Brush loose dust off gently first, then wipe with a soft damp cloth. Rubbing dust dry works like sandpaper on a fresh polish.
We polish stainless rails, hardware, bar equipment and marine fittings. Stainless is tough to cut but holds a polish for years.
Yes. Aluminum gets its own compounds and wheels so it comes out bright instead of burned or smeared.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.