Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Tumbling is how we give plated hardware a tumbled antique finish without hand work on every piece. Everything comes to us from Richmond by mail, and a free written quote for your plated hardware needs only photos and a part count.
Plating prep or final finish, we handle plated hardware both ways
Nobody likes opening a box and finding the wrong finish on four hundred parts. So before we run a full batch, we tumble a few pieces and make sure the look is what you asked for. If you're in Richmond, we can send photos of the sample so you can say yes or ask for a change.
Once the sample is approved, the full batch runs with the media and cycle time we settled on. Parts are rinsed, dried so they don't spot, and checked for stuck media and any burrs we missed.
Any parts you send, whether from Richmond, Glen Allen or Midlothian, get the same careful handling. We keep each part number separate, bag it, label it and ship it back insured.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
From plain deburring to a worn antique look, these are the finishes we offer on plated hardware sent in from Richmond. Many batches of plated hardware use more than one, in stages.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Over three decades of plating, one shop in Oceanside.
Every part is stripped, prepped, plated and inspected in our own building, and our work comes with a 12 month workmanship guarantee. Send photos and we'll take it from there.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Wherever you are, from Richmond to Midlothian, a batch of plated hardware moves through the same six steps.
Tell us what the parts are, how many you have and the finish you are after.
Ship from Richmond or Glen Allen the same way: strong box, labeled bags, a printed sheet with your quote number and part numbers, and insurance for the full value of the plated hardware.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
A lot of different trades use tumbled parts, and plated hardware turn up in many of them. If yours isn't listed here, send photos of your plated hardware anyway and we'll tell you if tumbling suits them.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Tell us the plan for plated hardware, we'll run the parts
Keep different parts apart. Each part number of your plated hardware should have its own bag and its own label, because mixing sizes and metals in one bag slows sorting and can scratch softer pieces on the way to us.
Add a printed sheet to the box of plated hardware with your name, phone, email, quote number and part numbers. It keeps the order straight when it reaches Oceanside, and it saves a phone call later if a question comes up about a tumbled antique finish.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
You can ship from any state, and Richmond and Glen Allen are no different. Four simple steps keep your plated hardware safe on the way to us.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Richmond sits along the James River in central Virginia, where you get hot, humid summers and mild winters. Neither changes how we work: a written quote first, a sample, then your full batch, shipped back insured to Glen Allen or wherever you are.
Browse tumble finishing pages for more places near Richmond, Petersburg and the towns around them.
Frequently Asked Questions
Short answers first, details second, for plated hardware. Use these to plan a batch of plated hardware from Richmond, and call if you'd like to talk it through.
Yes, with a good box. Small metal parts are heavy, so use a strong carton, fill the gaps and insure the box for the real value of the plated hardware. We pack the finished plated hardware the same way for the trip back.
It depends on the count. A few dozen pieces or more of plated hardware is a good fit for tumbling. For just a handful of plated hardware, hand polishing can cost less, and we'll tell you honestly after we see your photos.
Yes, when the media fits the metal. Soft metals like aluminum, zinc and brass run with lighter media and shorter cycles so details and dimensions on plated hardware are protected. We keep hard and soft parts in separate loads, because heavy pieces can ding and scratch softer plated hardware.
Wet steel can flash rust quickly, so we rinse plated hardware and dry them right away, spot free. Your plated hardware are checked before packing, and if plating is next, that step follows soon after. Ask us about clear lacquer if the plated hardware will stay bare.
Yes, and we recommend it. We tumble a few pieces first so you can see and approve a tumbled antique finish before the rest of the batch runs. We can send photos of the sample plated hardware when you need them, which keeps surprises to a minimum.
The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.
Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.
When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.