Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
We can give lighting parts and finials a clean, even finish, by the batch, at our Oceanside shop. Jobs from Salt Lake City start with photos of your lighting parts, a part count and a free written quote, and nothing ships until you have a quote number.
Small shop, steady hands, and plenty of lighting parts and finials
The look you end up with comes down to the media and the cycle, and both get chosen up front. Ceramic cuts fast, plastic is gentle, porcelain leaves things smooth, and stainless steel pins burnish instead of cut. Our Oceanside shop uses all of them, and we match the choice to your metal.
That's the kind of detail we sort out over email and photos, whether you're in Salt Lake City, Murray or Sandy. It doesn't take long, and it saves you from ordering a finish that looks nothing like what you pictured.
After that, the plan is easy: a sample run, your approval, and then the full batch. Standard turnaround is 3 to 5 weeks, and expedited orders of 5 to 7 business days are possible when our schedule allows.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Here's what we run in our tumblers every week, including lighting parts and finials. Pick the one closest to your lighting parts, and send photos if you're not sure which one fits.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
We keep the process simple, and it works the same way whether your lighting parts and finials ship from Salt Lake City or Murray.
Tell us what the parts are, how many you have and the finish you are after.
Wrap anything fragile, fill the gaps around your lighting parts and finials and seal the box well. Your lighting parts travel to Oceanside insured, and we need the tracking number by email as soon as it's on its way.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Tumbling serves a wide mix of businesses. These are the kinds of work we finish most, and lighting parts and finials from Salt Lake City can fit any of them.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Think it through, then send the lighting parts and finials over
Photos help more than almost anything else. Take a few clear shots of your lighting parts and finials in good light, one of the whole group and a couple up close. Add a photo of the finish you'd like on your lighting parts if you have an example.
Tell us about the metal, too. Brass, steel and stainless can take stronger media, while aluminum and zinc need a lighter touch, which matters for lighting parts and finials. If you aren't sure what your lighting parts are made of, say so and we'll help figure it out.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Mailing lighting parts and finials from Sandy or Salt Lake City follows the same four steps, and a few minutes of packing now saves days later.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Out in Salt Lake City, in the Salt Lake Valley below the Wasatch Mountains, you don't have to make the trip. Send photos of your lighting parts and finials, get a written quote, and ship the box when your quote number comes through. West Valley City works the same way.
If you're closer to Murray than Salt Lake City, one of these nearby pages may fit better.
Frequently Asked Questions
Here are straight answers to the questions people ask before sending lighting parts and finials from Salt Lake City. Don't see yours? Call us or send a message.
No. Drop off is available at our Oceanside shop if you call ahead, and customers near Murray can ship by mail instead. Shipping works well. You pack the lighting parts and finials, we finish them, and everything comes back insured and packed by part number.
We run compounds and water in the tumbler, and spot free drying afterward keeps lighting parts and finials looking clean. For long term protection of lighting parts, we can add a clear lacquer, and we'll suggest whether to leave them bare or seal them based on how they'll be used.
Wet steel can flash rust quickly, so we rinse lighting parts and finials and dry them right away, spot free. Your lighting parts are checked before packing, and if plating is next, that step follows soon after. Ask us about clear lacquer if the lighting parts will stay bare.
Yes, and we recommend it. We tumble a few pieces first so you can see and approve a clean, even finish before the rest of the batch runs. We can send photos of the sample lighting parts and finials when you need them, which keeps surprises to a minimum.
Burnishing uses small steel shapes that press lighting parts and finials smooth instead of cutting the surface away. On lighting parts the result is a bright, clean shine without buffing each piece by hand, and almost no metal is removed in the process.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.