Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
From New Braunfels to San Antonio and beyond, stainless steel fittings can ship to our Oceanside shop and come back finished. We run a sample first, then the full batch, and your stainless fittings return insured and packed by part number.
We test first, then run stainless steel fittings the whole way through
A tumbler looks simple from the outside, but the result depends on a lot of small choices. Which media goes in, how long the cycle runs, whether the load is wet or dry. We make those calls for every batch, whether it ships from San Antonio, New Braunfels or somewhere much farther away.
Hard metals like steel and stainless can take aggressive media. Soft ones like brass, aluminum and zinc can't, or the details wash away. That's why we never mix hard and soft parts in one load, and why a quick photo from you helps us pick the right setup before anything runs.
If you're sending parts from San Antonio, mention any holes, slots or threads. Media can wedge into openings close to its own size, and it's much easier to plan around that on the front end than to dig it out later.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Every batch starts with the same question: what should your stainless steel fittings feel and look like when they're done? For stainless fittings, these are the finishes we can give you.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Getting an even satin surface on stainless steel fittings takes six steps, and you only handle the first two.
Tell us what the parts are, how many you have and the finish you are after.
Once your quote number arrives, ship your stainless steel fittings from San Antonio to our shop in Oceanside. A strong box, labeled bags and insurance for the real value will keep your stainless fittings safe on the road.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Some customers send a few dozen stainless steel fittings and some send thousands. These are the groups we serve most, and your stainless fittings may fit one of them.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Get stainless steel fittings right on the first run
Write down any holes, slots or threads on your stainless steel fittings. Media can wedge into openings close to its own size, so we pick a shape and size that stays clear of the openings on stainless fittings, and we check every finished piece for anything stuck.
If any of your stainless steel fittings have a thread or a tight fit that has to stay exact, mention it when you ask for a quote from San Antonio. Tumbling takes very little metal off stainless fittings, but we'd rather plan for it than guess.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Small metal parts like stainless steel fittings travel well when they're packed right. Here's how to send a box of stainless fittings from San Antonio to our Oceanside shop.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
San Antonio sits in south central Texas, a long way from our Oceanside shop, so tumbling by mail is the practical choice. Photos first, then a quote number, then a strong insured box for the stainless steel fittings. Shipping from New Braunfels or Schertz works exactly the same way.
Near San Antonio or around Boerne? These pages cover other places we serve by mail, much like New Braunfels.
Frequently Asked Questions
Quick answers for San Antonio customers, and anyone near New Braunfels curious about how tumble finishing works. Ask us if something is missing.
Yes. Our process doesn't change by location, so shipping stainless steel fittings from New Braunfels, Schertz or San Antonio follows the same steps: photos, a quote number, labeled bags, a strong insured box and a tracking number sent by email.
Yes. Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on your stainless steel fittings smoother. We do the plating in the same Oceanside shop, so your stainless fittings never have to travel between vendors.
Yes. We pick the media and cycle time for the metal, run a sample of your stainless steel fittings so you can approve the result, and then finish the full batch. If you have a piece with the look you want, send it or a photo and we'll match it as closely as we can on your stainless fittings.
The popular ones for stainless steel fittings are satin tumbled, bright burnished, soft matte and aged tumbled brass. We also do tumbled antique over plating, worn edge highlights and tumbled and lacquered finishes on stainless fittings. Send an example of the look you want on your stainless fittings and we'll match it as closely as we can.
Tumbling finishes many pieces at once and gives the same result on every one, so cost per part of stainless steel fittings drops as quantity goes up. Hand polishing can bring a true mirror shine to flat faces and keeps edges sharp, but each piece is handled one at a time, which adds up fast on stainless fittings. For stainless fittings, we'll suggest the better fit after seeing your photos.
The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.
Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.
When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.