Railings and Gates
Wrought iron and steel railings, gate panels and balusters stripped of rust and flaking paint, then powder coated or plated to stand up to weather again.
Restoring metal is what we do every day at our Oceanside shop. You can send heirlooms, fixtures, furniture and outdoor pieces from San Antonio, and we send back a clear plan and a written price.
Crated, insured and tracked all the way
Iron, steel, brass, bronze, aluminum, copper and pot metal all show up at our door, and each one ages in its own way. If you are holding something from San Antonio and do not know what it is made of, a magnet and a photo tell us a lot.
We figure out the metal first because it decides everything that follows, from how we strip it to which finish will stick. Decorative Metal Coatings has done this in Oceanside, California since 1989, and we would rather identify a piece correctly than guess.
If you live in New Braunfels, Boerne or Schertz, send pictures of a scratched spot or a worn edge, and we will explain what we see before we recommend anything.
Start with a few photos. Tell us what the piece is, where it lives and how you want it to look, and we will explain what it needs, what it will cost and how long it will take before anything leaves your hands.
Take a look at the pieces we restore most, and send photos of yours if you do not see it listed.
Wrought iron and steel railings, gate panels and balusters stripped of rust and flaking paint, then powder coated or plated to stand up to weather again.
Chandeliers, sconces, lamp bases and stands taken apart, cleaned, refinished arm by arm and returned ready for your electrician to rewire.
Outdoor sculptures, fountains and birdbaths cleaned of corrosion and mineral stains, repatinated or sealed so they age gracefully instead of falling apart.
Cabinet pulls, drawer handles and decorative knobs restored with a durable finish that brings back their original beauty, with options ranging from classic designs to modern styles.
Antique hardware, candlesticks, clocks and keepsakes handled with care, cleaned and refinished while engraving, stamps and fine detail are preserved.
Dedication plaques, address numbers, metal signs and wall art brought back to crisp, readable condition with lettering and relief kept sharp.
Five clear steps, and you approve the quote before we begin any work.
Show us the whole piece and any close ups of rust, breaks or missing parts, plus rough dimensions.
We identify the metal and its condition, suggest the best finish and send a written quote within 24 business hours.
Box the piece with at least three inches of padding, declare the real value with the carrier and send it to Oceanside. Gates and railings are crated.
Old coatings and rust come off, bends are straightened, pits are filled and the surface is polished or blasted.
The new finish is applied, every detail is checked and the piece is packed and returned insured.
The right finish depends on where the piece lives and how it is used. We help you choose before any work begins.
Drag the handle on any photo to see the piece as it came in and as it went home.
Before
Blackened brass with flaking lacquer on every arm. Taken apart, stripped, polished and refinished in bright brass, then sealed so the shine lasts.
Before
Years of rust, chipped paint and weather exposure. Stripped down to bare metal, restored and finished with a durable matte black coating built for long-lasting performance.
Before
Green corrosion hid most of the lettering. Cleaned, given a new dark patina, raised letters polished bright and sealed against the weather.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
Each metal ages in its own way, so each one needs its own cleaning, repair and finish.
Rust is removed down to clean metal and any weak spots are checked before a protective finish goes on. Powder coat or plating both work well.
Tarnish and old lacquer are stripped so the metal can be polished, replated or given a new patina, depending on the look you want.
Light and corrosion resistant, but chalky and pitted with age. Cleaned and refinished in powder coat or plated after the right pretreatment.
Copper pieces can be polished bright and sealed, or cleaned and darkened to an even antique tone that hides fingerprints.
Common in old lamps and fixtures. Fragile and porous, so we strip it gently and fill pits by hand. Slow work that many shops turn down.
Pieces with glass, wood, stone or old paint attached are reviewed case by case. Send photos and we will explain what can be removed safely.
The pieces, finishes and repair work that make up a typical refurbishing job in our shop.
Since 1989 we have been rescuing metal pieces that other people gave up on. Homeowners, designers, collectors and businesses trust us because every finish we offer is done in house, so the advice we give is about your piece, not our shortcuts.
Send a photo of your part and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
One heirloom or a full set of furniture, shipped to us from any state and returned insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
If you manage a property, collect antiques or just own something special, you are in good company.
Brass rails, slot trim, light fixtures, signage and decorative metal refreshed between renovations, often in large matched sets. Trusted by casino resorts across North County San Diego.
Bar stools, patio sets, railings and lobby fixtures restored for a fraction of the cost of replacing a whole room.
Family heirlooms, entry gates, light fixtures and garden pieces brought back so they can stay in the home.
Entry gates, pool fencing panels, mailboxes and address signs refinished to keep a community looking cared for.
Salvaged and vintage metal reworked in a new finish to fit a modern design, matched across every room of a project.
Careful cleaning and refinishing that respects age and value, with the option to keep original patina where it matters.
Every piece that comes through our door has a story. Our job is to give it a better next chapter, not to erase what made it worth saving.
If a piece is not worth refurbishing, or needs work outside what we do, we tell you before you spend a dollar.
Engraving, castings, stamps and maker marks are protected during stripping and polishing so the character of the piece survives.
Outdoor pieces get finishes built for sun and salt air, indoor pieces get finishes chosen for looks and easy care.
Every refurbished piece is wrapped, padded and boxed with care, and large items are crated when needed.
A quick way to weigh your options
Pick the piece up and look at it closely. Clean lines, sharp castings and sturdy joints suggest it was made to last. Those are the pieces that repay a refinish, because the hard part is already done.
Then ask what the damage really is. Most pieces that come to our shop are weathered, not broken. A bent arm or a few pits can be straightened or filled, so surface wear alone is rarely a reason to give up.
Then think about what the piece means and what it would cost to replace with the same quality. Vintage lighting, cast garden pieces, ornamental iron and antique hardware are rarely made the same way anymore. Refurbishing often costs less than a new item of equal build, and the result is one of a kind.
Finally, consider where it will live. A piece moving from indoors to a patio may need a different finish than it had before. Tell us its new home and we will choose a finish that will hold up there.
Metal Finishing Gallery
A look at recent work from our Oceanside shop: plated hardware, lighting, hospitality and casino pieces, marine fittings and industrial parts.
You do not need to be near Oceanside to use our shop. These steps get a piece from San Antonio to us in good shape.
Send photos of each piece with rough dimensions and the finish you have in mind. You receive a written quote and lead time, usually the same business day. Always wait for a quote number before shipping.
Wrap small pieces individually with at least three inches of padding. Remove glass shades and crystals from fixtures and pack them separately. Gates, railings and furniture should be crated or palletized.
Declare the real value with the carrier and email us the tracking number so we can log your pieces the day they arrive.
When the work is done we photograph the finished pieces for your approval, then pack them in fresh materials and ship them back insured.
Every refurbishing job is stripped, repaired, refinished and inspected in our own facility in North County San Diego.
Metal refurbishing, plating, powder coating and patinas in San Diego County since 1989.
San Antonio has a long history of wrought iron, from courtyard gates and balconies to lanterns and garden pieces. Hot summers, humid air and strong sun are hard on all of it. Powder coat is our usual choice for outdoor iron, and shipping between Texas and Oceanside usually takes 2 to 4 days each way.
We ship to and from the cities below as well, and each has its own page.
Frequently Asked Questions
If you are thinking about refurbishing a piece from San Antonio, these answers may save you a phone call.
Heavy gates should be crated or palletized and sent by freight. Get a quote first, then schedule the delivery with us, especially if a liftgate is needed. Insure the shipment for its real value and email us the tracking number.
Yes. We take pieces from any state, and the steps are simple: get a quote, pack the piece with plenty of padding, insure it and send us the tracking number. We pack it again and ship it back insured.
Yes, as long as each piece is wrapped separately with plenty of padding. Include a printed list of every piece and the finish you want for each, and keep screws and small parts in labeled bags.
Yes. We clean off corrosion and mineral stains, then repatinate or seal the bronze so it ages gracefully. We can also keep the original tone if you prefer. Send photos of the whole piece and close ups of the problem areas.
There is a wide range of colors and textures, from satin black to bright shades. Send a sample or tell us the look you want, and we will recommend a color that suits the piece and where it will be used.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.