Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Send photos and a part count from Philadelphia and we'll send back a free written quote. We run a sample, you approve the look, then the full batch goes in the tumbler.
A finish you see before we commit
Not sure what finish you need? That's a normal place to start. Tell us what your parts are, how many there are and where they'll be used, and we'll point you to satin tumbled, bright burnished, soft matte or an aged look.
If tumbling isn't the right fit, we'll say so. Large or delicate pieces and parts that need a true mirror shine often do better with hand polishing, and we offer that too. People in Philadelphia get an honest recommendation either way.
The quote is free, written and based on your photos. Pricing depends on part size, count, metal, starting condition and finish, so the more you tell us, the closer the number will be. Parts from Norristown, Media and Conshohocken are quoted the same way.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Tumbling can do a lot more than knock off burrs. Here are the services we offer for parts coming from Philadelphia.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Over three decades of plating, one shop in Oceanside.
Every part is stripped, prepped, plated and inspected in our own building, and our work comes with a 12 month workmanship guarantee. Send photos and we'll take it from there.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Each job moves through the same steps, whether it's a few dozen pieces or a full production run from Philadelphia.
Tell us what the parts are, how many you have and the finish you are after.
Once your quote number arrives, box up the parts in Philadelphia with each part number in its own labeled bag. Ship to Oceanside and send us the tracking number.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Plenty of different trades use tumbling to get parts ready. These are the businesses and projects we help, with Philadelphia parts always welcome.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Think it through once, save time later
Tell us what the finish needs to do. Is it for looks, for safe handling or for a smoother surface before plating? The answer changes which media we reach for and how long the cycle runs.
You don't need technical terms. Words like smoother, brighter, softer or older are plenty, and a photo says even more. We translate it from there for your Philadelphia project.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
From first quote to return shipment, mailing parts from Philadelphia takes a few minutes of setup. This is what we ask you to do.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Philadelphia has block after block of older brick homes and buildings, and their hardware often needs a gentle refresh. Send photos of the pieces and tell us the look you're after, from soft satin to worn and aged. Parts ship cross country in one box and come back insured.
You may know shops or friends in towns near Philadelphia. Their tumble finishing pages are listed here.
Frequently Asked Questions
If you're weighing your options, these answers should help. Anything else, just ask.
Yes, boat, yacht, classic car and motorcycle parts are part of our work. Small pieces like cleats, latches, badges and trim can be tumbled for an even surface before plating or polishing.
Yes. Aged tumbled brass and tumbled antique finishes suit renovations where new pieces need to blend with old ones. We darken and tumble so the edges wear back to bare brass. Send a photo of what you're matching and we'll run a sample first.
Parts move in a drum with small pieces of media and a liquid compound. Over time the media wears away burrs, rounds sharp corners and smooths the surface. Depending on the media, it can also brighten the metal or give it a soft satin look.
It depends on the job. Tumbling is great for many parts at once, gives the same result on every piece and costs less per part. Hand polishing suits large or delicate pieces, flat faces that need a true mirror shine and edges that must stay sharp.
Tumbling usually pays off from a few dozen parts up. For only a handful of pieces, hand polishing may fit better. Send photos and your count, and we'll tell you honestly which way to go.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.