Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Send us machined steel parts from Tulsa and we'll bring them back with clean, burr free edges. We choose the media for the metal, check every batch for lodged media and pack the machined parts by part number before they go home insured.
Everything machined steel parts need, under one roof
Most parts that get tumbled are headed somewhere else next. Plating, a patina, a coat of lacquer. When we do all of that in one shop, your Tulsa order doesn't get shipped around between vendors, and one team knows the whole story of your machined steel parts.
Tumbling first makes the next step better. It removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and looks better for less cost. Brass pieces can also be darkened and then tumbled, so the high points wear back to bright metal.
If your machined steel parts will stay unplated, that's fine too. We finish them, dry them and pack them. Whether they came from Tulsa, Broken Arrow or Jenks, they go home insured.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Machined steel parts shipped from Tulsa don't all need the same thing. Some need burrs gone, some need clean, burr free edges, and some are heading for assembly and plating next. Tell us which one fits your machined parts.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Your machined steel parts follow these steps from the moment you ask for a quote in Tulsa until they come home.
Tell us what the parts are, how many you have and the finish you are after.
Send the box of machined steel parts to our Oceanside address, 2613 Temple Heights Dr, Ste G. Put a sheet inside with your name, phone, email and quote number, and email the tracking number for your machined parts as soon as you have it.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Tumbling isn't only for one kind of business, and machined steel parts are a good example. Here's a look at who uses it and why, whatever the size of your order of machined parts.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
A little prep gives machined steel parts a better finish
Start by counting. Give us the total number of machined steel parts and how many of each part number are in the box. It helps us pick the right size of load and gives you a firm quote on the batch of machined parts you're sending from Tulsa.
Then think about the edges. Tumbling rounds corners a little, which most machined steel parts need, but some must stay sharp for a reason. If a sharp edge matters or your machined parts have a tight fit, say so before we quote and we'll plan around it.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
A good box makes all the difference. Follow these steps when you send machined steel parts from Tulsa and we'll take it from there.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Out in Tulsa, in northeastern Oklahoma along the Arkansas River, you don't have to make the trip. Send photos of your machined steel parts, get a written quote, and ship the box when your quote number comes through. Sand Springs works the same way.
More tumble finishing pages for places close to Tulsa, including Broken Arrow, are listed here.
Frequently Asked Questions
We like questions about machined steel parts, because they lead to better finishes. These are good ones to read before you send machined parts from Tulsa.
Put in a printed sheet with your name, phone number and email, the quote number, part numbers with quantities, the finish you want on the machined steel parts and any next step like plating. Keep each part number of machined parts in its own labeled bag.
We run compounds and water in the tumbler, and spot free drying afterward keeps machined steel parts looking clean. For long term protection of machined parts, we can add a clear lacquer, and we'll suggest whether to leave them bare or seal them based on how they'll be used.
Burnishing uses small steel shapes that press machined steel parts smooth instead of cutting the surface away. On machined parts the result is a bright, clean shine without buffing each piece by hand, and almost no metal is removed in the process.
Yes, lightly. A short tumble over plated or darkened parts wears the high points through and gives machined steel parts an antique, lived in look. Too much time cuts through the finish, so we review jobs with machined parts first and usually run a sample.
It often does. Tumbling takes off burrs, rounds sharp edges and gives an even surface, which suits parts going to assembly and plating. Tell us about the application and any tight fits on the machined steel parts, and we'll plan the media and cycle around it.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.