Skip to content

Your Cincinnati Source for Tumble Finishing Services

Plating next? Start with a smoother base

From a few dozen pieces to a full production run, we run the tumbler so you do not have to sand and file by hand. Cincinnati orders are welcome.

Certified, Approved and Verified

Cincinnati Tumble Finishing for Hardware, Castings and Parts

Why people in Cincinnati send us their parts

Tumble finishing is one of those services people only appreciate once they have tried it. A box of rough castings goes in, and a box of smooth, evenly finished parts comes out. For parts from Cincinnati we do this by the batch, from a few dozen pieces to a full production run.

The secret is in choosing the right media. Hard ceramic takes down burrs on steel, gentler plastic protects brass and zinc, and fine porcelain leaves a bright surface. We pick the combination for your metal and your parts instead of using one setup for everything.

That is the same care a batch from Blue Ash, Mason or Norwood would get. Parts arrive by carrier from all over the country, and we ship every batch back insured.

Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.

What We Do

Tumble Finishing Services

Tumbling is more than one process. These are the main ways we use it to finish metal parts, whether they come from OH or anywhere else in the country.

Small machined metal parts after tumble deburring

Deburring

Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.

Metal parts with softly rounded edges after tumbling

Edge Smoothing

Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.

Brightly burnished brass parts from a steel media tumbler

Burnishing

Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.

Brass hardware with a soft decorative tumbled finish

Decorative Tumbled Look

A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.

Steel parts tumbled smooth and ready for plating

Prep Before Plating

Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.

Plated hardware tumbled for an antique worn look

Tumbled Antique Finish

Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.

Tumbling Results

Before and After

Drag the handle across each photo to see parts as they went into the tumbler and as they came out.

Cast brass hinges after tumble finishing
Rough cast brass hinges before tumbling Before
After

Cast Brass Hinges

Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.

SATIN TUMBLED BRASS HARDWARE SET
Machined steel parts after tumble deburring
Machined steel parts with burrs before tumbling Before
After

Machined Steel Parts

Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.

DEBURRED STEEL PRODUCTION RUN
Brass knobs with an aged tumbled finish
New shiny brass knobs before an aged tumbled finish Before
After

Aged Brass Knobs

Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.

AGED TUMBLED BRASS RESTORATION
Free Quotes

Not sure what your part needs? Send us a photo.

We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.

Tap to add photos (up to 5). JPG, PNG, WEBP or iPhone HEIC.
    What Our Clients Say

    Trusted by Professionals

    From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.

    Choosing the Right Approach

    Tumbled, Hand Polished or Both

    Each method has its place. The right one depends on how many parts you have, their shape and the look you want.

    By the batch

    Tumble Finishing

    • Many parts finished at once
    • Same result on every piece
    • Reaches corners and recesses
    • Softens edges as it smooths
    • Lower cost per part
    One at a time

    Hand Polishing

    • True mirror shine on flat faces
    • Keeps edges crisp and sharp
    • Better for large or delicate pieces
    • Each part handled individually
    • Higher cost per part
    Best of both

    Tumble Then Plate

    • Burrs and marks removed first
    • Smoother base for the plating
    • Less hand work before plating
    • Even look across a full run
    • Common for production hardware
    Behind the Finish

    The Media Makes the Difference

    The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.

    Fast cutting

    Ceramic Media

    Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.

    Soft metals

    Plastic Media

    Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.

    Pre polish

    Porcelain Media

    Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.

    Burnishing

    Stainless Steel Media

    Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.

    Dry finish

    Walnut Shell and Corn Cob

    Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.

    Often overlooked

    Compounds and Water

    The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.

    How It Works

    Our Tumble Finishing Process

    It starts with a photo and ends with parts packed by part number. Here is everything in between.

    1

    Photos and Part Count

    Tell us what the parts are, how many you have and the finish you are after.

    2

    Ship or Drop Off

    Small parts travel well. Box them tightly in Cincinnati, insure the shipment and send it our way.

    3

    Sample Run

    We tumble a few pieces first so you can see and approve the finish before the full batch.

    4

    Full Batch

    Parts run with the media and cycle time dialed in from the sample, in stages when needed.

    5

    Rinse, Dry and Check

    Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.

    6

    Plate or Pack

    Parts move on to plating or patina, or are packed by part number and shipped back insured.

    What We Can Tumble

    Metals We Tumble Finish

    Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.

    Most popular

    Brass, Bronze and Copper

    Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.

    All finishes

    Steel

    Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.

    All finishes

    Stainless Steel

    Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.

    Gentle cycles

    Aluminum

    Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.

    Our specialty

    Zinc Die Cast

    Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.

    Ask us first

    Plated and Finished Parts

    Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.

    Freshly tumbled brass parts being checked in the shop
    Plating line at Decorative Metal Coatings
    35+ Years of Expertise
    Take a Moment to Learn More

    About Decorative Metal Coatings

    Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.

    Free Estimates Available

    Send photos and a part count and receive a no obligation quote within 24 hours.

    Quality Guaranteed

    Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.

    Ship From Anywhere in the US

    Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.

    Fast Turnaround Times

    Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.

    Tumble Finishing Catalog

    Services, Looks and Pairings

    Everything we do in the tumbler, the finishes it creates and the services that often follow.

    Tumble Services

    • Deburring
    • Edge Smoothing
    • Scale and Light Rust Removal
    • Burnishing
    • Pre Polishing
    • Spot Free Drying
    • Staged Multi Step Runs
    • Sample Runs

    Finish Looks

    • Satin Tumbled
    • Bright Burnished
    • Soft Matte
    • Aged Tumbled Brass
    • Tumbled Antique Over Plating
    • Worn Edge Highlight
    • Tumbled and Lacquered

    Paired Services

    • Copper Plating
    • Nickel Plating
    • Chrome Plating
    • Brass Plating
    • Patina Finishes
    • Powder Coating
    • Clear Lacquer
    • Sample Matching
    Our Commitment

    Every Batch Done Right

    Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.

    Sample First

    A few parts are run and approved before the full batch, so there are no surprises when the rest come out.

    Right Media for the Part

    Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.

    Checked Piece by Piece

    Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.

    Kept by Part Number

    Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.

    What We Do Differently

    • We run a sample and get your approval first
    • Hard and soft parts are never mixed in one load
    • Parts with holes and threads are checked for stuck media
    • Steel is dried fast so it does not flash rust
    • Tumbling and plating happen in the same shop

    What You May Experience Elsewhere

    • Full batches run blind with no sample
    • Mixed loads that ding and scratch softer parts
    • Media left stuck in holes and threads
    • Water spots and flash rust on returned parts
    • Parts shipped between shops for each step
    Who We Serve

    Who Relies on Our Tumbling

    We finish parts for many trades. A few of the most common ones are below.

    Tumbled brass trim pieces and small hardware for a casino resort

    Casinos and Gaming

    Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.

    Tumbled brass door and cabinet hardware

    Architectural Hardware

    Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.

    Batch of deburred machined parts

    Machine Shops and Manufacturers

    Production parts deburred and smoothed in volume, ready for plating, coating or assembly.

    Tumbled metal hardware on a wooden cabinet

    Furniture and Cabinetry

    Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.

    Tumbled brass lighting components

    Lighting and Fixtures

    Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.

    Tumbled brass belt buckles and keychains

    Makers and Small Brands

    Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.

    Batch Prep for Tumble Finishing in OH

    What we need to know to get it right

    Give us the full picture when you contact us from Cincinnati. The metal, the part count, the finish, the next step and any limits on size or edges all go into the quote.

    The more we know, the fewer questions we have to ask later, and the faster we can get you a written quote and a sample run on the schedule.

    Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.

    Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.

    Nationwide Service

    Ship Your Parts by the Box From Anywhere in the US

    Mail your parts from Cincinnati and skip the hand work. This is how a shipped order works from quote to return.

    01

    Get a quote first

    Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.

    02

    Bag by part number

    Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.

    03

    Pack it tight

    Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.

    04

    Finished and returned

    We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.

    Visit Us

    Our Location

    Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.

    Decorative Metal Coatings

    Tumble finishing, plating and patina under one roof since 1989.

    Business Hours

    • Monday to Friday 8:00 AM to 5:00 PM
    • Saturday 9:00 AM to 2:00 PM
    • Sunday Closed

    Working with Cincinnati, near or far

    Cincinnati grew up on the Ohio River, with old brick neighborhoods and a long tradition of toolmaking and machine work. Whatever your project looks like, the steps are the same. Send photos, get a written quote and approve a sample before the full run.

    Nearby Cities We Serve

    If you work across several cities in this region, these pages may help.

    Tumble Finish Help for Cincinnati Customers

    Frequently Asked Questions

    Tumbling is easy to get wrong without the right media and timing. These answers explain how we handle it.

    A written price based on your photos and part count, plus our suggestion for the finish and a lead time. There is no charge and no obligation.

    Call our Oceanside shop at (760) 746 3378 or send photos through the quote request page. A written quote follows.

    Quotes are usually sent within 24 hours, and often the same business day.

    Yes. Hinges, pulls, knobs and other hardware are some of the most common things we tumble. We match the finish across the set so every piece looks the same.

    Light rust and scale come off in the tumbler. Heavy rust or pitting may need other work first, so send photos and we will tell you what to expect.

    The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.

    Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.

    When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.