Show Chrome Restoration
Triple plated in copper, nickel and chrome and buffed by hand between layers, for the deep, wet shine that makes small trim stand out on a finished build.
Decorative Metal Coatings has been restoring plated parts since 1989. Show us what you have in St Paul, and we will give you a written quote from photos, free.
Chrome and nickel work you can look at up close
We started plating in 1989, and one thing we learned early is that people do not mind hearing the truth about their parts. If a piece from St Paul is too far gone to save, we tell you before we start, not after.
When a part can be saved, we show you what we found. Photos go out when a decision is needed, and every finished piece is checked under light for haze, pits and missed spots before it leaves the shop.
That is how we would treat a part from Roseville, Maplewood or Woodbury, too. It is simple, and it keeps surprises to a minimum.
Small parts are our sweet spot, and they are easy and affordable to ship from anywhere in the country. Send a few photos, tell us what the parts came from and how you want them to look, and we will send back a written quote.
Every service below is done by hand where it counts, from leveling pits to buffing between layers.
Triple plated in copper, nickel and chrome and buffed by hand between layers, for the deep, wet shine that makes small trim stand out on a finished build.
Pitted and blistered pot metal is stripped, filled and leveled in copper before it is plated. Slow, careful work that saves parts most shops send back.
Bright or satin nickel for earlier cars and motorcycles that left the factory with a softer, warmer shine than modern chrome.
Knobs, handles, window cranks, bezels and switch plates restored so the inside of your classic matches the outside.
Levers, clamps, mirror stems, small covers and controls replated so a vintage bike looks right from every angle.
Original bolts, nuts, clips and small brackets cleaned and replated, so you keep correct factory hardware instead of buying generic replacements.
Drag the handle on any photo to see the part as it arrived and as it left our shop.
Before
Bubbled, flaking chrome over pitted pot metal. Stripped, filled in copper, leveled by hand and triple plated in show chrome.
Before
A thin steel ring with surface rust and worn plating. Stripped, polished and finished in bright nickel and chrome.
Before
A coffee can full of rusty original bolts, clips and small brackets. Cleaned, sorted and replated as a matching set, ready to go back on.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
Owners, shops and collectors trust us with parts that are hard or impossible to replace.
Not every part needs the same treatment. Picking the right level for each piece keeps your budget where it matters most.
Classic parts were made from a handful of metals, and each one needs its own preparation before it can shine again.
Used for door handles, hood ornaments, interior knobs and many trim pieces. We stop the pitting, fill it in copper and level it by hand before plating.
Brackets, bezels, levers and hardware. Rust is removed down to clean metal, then the part is polished and plated in copper, nickel and chrome.
Common on early vehicles, lamps and fittings. Brass takes nickel and chrome beautifully once it has been cleaned and polished.
Some trim pieces and motorcycle covers are aluminum. They need a special pretreatment before plating, so we review each piece before quoting.
Many classic trim pieces are stainless and may only need polishing. If yours does need plating, it gets a nickel strike first so the finish bonds.
Older fittings and hardware in copper or bronze clean up well and plate easily, whether you want them chromed or nickeled.
No guesswork, no surprises. This is what happens from your first photo to the day your parts come home.
Photograph each part from a few angles and tell us what it came from and the finish you want.
We check the condition and the metal, then send a written quote and lead time within 24 business hours.
Pack each part on its own in a snug box and ship it to our Oceanside shop. Please wait for your quote number first.
Old plating and rust come off, pits are filled, and the surface is leveled and polished by hand.
Copper, nickel and chrome go on in layers, then every part is inspected, packed and returned insured.
What Size Parts Make Sense to Ship
Most of the classic and vintage work that comes through our door fits in a small box. Handles, knobs, bezels, levers, brackets, hardware and short trim pieces are light, they pack easily and the shipping cost both ways stays reasonable. For owners outside California, these are the parts where mailing them to a specialty shop makes the most sense.
Larger pieces like bumpers, grilles and full length trim are a different story. We can plate them, but they need oversized boxes or freight, and the trip here and back can add up quickly. If you live in Southern California, the easiest option is simply to bring them to the shop.
If you are farther away and still want us to handle a large part, we are happy to take a look. Send photos and measurements, we will quote the plating, and you can weigh that against the shipping before you decide. No pressure either way.
A quick list of the classic and vintage parts and finishes we handle most often.
We have been restoring plated parts since 1989. Car owners, motorcycle restorers and private collectors send us the pieces they cannot replace, because we take the time to save them.
Send photos of your parts and get a no obligation quote within 24 hours.
Every restored part is backed by our craftsmanship guarantee. If something is not right, we make it right.
Small parts travel easily from any state and come back to you insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
On a classic, people look closely. Every shortcut in stripping or prep shows up later as peeling, pits or haze, so we do the slow work first.
Old chrome and nickel are fully removed, so the new layers bond to clean metal instead of a finish that is already failing.
Copper is built up and leveled by hand until pits disappear, which is what separates a show finish from a quick rechrome.
Every part is checked for haze, pits and missed spots before it is approved to leave the shop.
Each restored part is wrapped on its own, so fresh chrome never rubs against another piece on the way home.
Different projects, same standards. Here is who we restore parts for.
Antique slot machine trim, handles and casino collectibles restored to their original shine. Casino resorts across North County San Diego trust us with their decorative metal work.
Private owners and restoration shops rebuilding American and European classics, one small part at a time.
Riders and builders bringing old bikes back to original condition, or giving a custom build a clean, bright finish.
Shops that need dependable show chrome on small parts, with clear quotes and consistent quality job after job.
Owners getting ready for shows and judging who need finishes that hold up under a very close look.
Collectors of automobilia and vintage hardware who want a treasured piece to look the way it did when it was new.
Keep your restored parts looking sharp
A fresh finish stays fresh when you give it a little attention. Wash restored chrome and nickel with mild soap and water, and dry it right away with a microfiber cloth. Water that dries on its own leaves spots, and spots are where trouble starts.
Minnesota winters bring deep cold and salted roads, and that salt is the worst thing for any plated trim. If you wax or seal your restored parts every few months, they will be much better prepared for it.
Skip steel wool, rubbing compound and harsh wheel cleaners. They scratch the surface and can cut through the chrome to the nickel underneath. If a spot needs more than soap, use a polish made for chrome and a soft cloth. Nickel is softer than chrome, so treat nickel parts gently and always dry them well.
For storage, keep parts and vehicles somewhere dry under a breathable cover, never plastic that traps moisture. If you notice small rust spots or lifting plating, send us a photo. Catching a problem early is always easier than waiting.
Restored Parts Gallery
Door handles, bezels, cranks, levers and original hardware from classic cars and vintage motorcycles, restored in our Oceanside shop.
Packing parts right protects them on the way here and keeps the shipping cost down. Here is what we recommend.
Send photos of every part and the finish you want. You will get a written quote and lead time, usually the same business day. Please wait for your quote number before you ship.
Wrap each part on its own so metal never touches metal, and use a box just large enough for the parts and padding. A snug box keeps parts safe and keeps the shipping cost down.
Bag and label small hardware by where it goes so sets come back together easily. Declare the real value with the carrier and email us the tracking number.
When your parts are finished we send photos for your approval, then pack them in fresh materials and ship them back insured.
Local car and motorcycle owners are welcome to drop off parts at our shop in North County San Diego. It is also the easiest option for larger pieces.
Chrome, nickel and copper restoration for classic and vintage parts since 1989.
Our shop is in Oceanside, California, and we ship finished parts back insured. Call (760) 746 3378 with any questions before you pack, and remember we work on Pacific time.
If you are around St Paul, these neighboring cities use the same process. Pick yours to see how it works there.
Frequently Asked Questions
Here are answers to the questions we hear most from classic car and motorcycle owners. If yours is not here, call us or send a message.
We can work from a sample. Send the part or a clear photo of it and tell us which piece has to match, and we will quote the job with that goal.
Yes. Peeling means the old plating has failed, so it has to come off completely. We strip to bare metal and rebuild the layers.
Yes. Finished parts are packed in fresh materials and shipped back insured. Declare the real value with the carrier when you send them to us, too.
To Decorative Metal Coatings, Attn: Receiving, 2613 Temple Heights Dr, Ste G, Oceanside, CA 92056. Please wait for your quote number first, and put it in the box.
Pot metal is a cast metal often used for door handles, hood ornaments, interior knobs and trim on older vehicles. It pits and blisters with age, which is why it needs careful repair before plating.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.