Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
We strip, repair and replate boat and yacht hardware in bright chrome, satin chrome or polished nickel. Send photos from Yucca Valley, get a free written quote and ship small pieces to our Oceanside shop in a regular box.
Marine Hardware Restored By Hand, Start to Finish
Marine hardware has a hard life. Salt air and moisture slip under the chrome and push it up from below, so a cleat that looks fine from the dock can be flaking a few months later. Polishing hides the problem for a while, but it does not stop it. For boat owners in Yucca Valley, that is usually the moment to call us.
Decorative Metal Coatings has been plating in Oceanside since 1989, and boat hardware is a regular part of our week. We strip the old finish all the way to bare metal, fill the pits and rope grooves with copper by hand, then build the new finish back up with nickel and chrome.
If you are in Twentynine Palms, Joshua Tree or Morongo Valley, the steps are the same as for Yucca Valley. Photos come first, then a padded box once you approve the quote. You do not have to make a drive just to find out whether a piece is worth saving.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Here are the pieces we restore most often. If yours is not on the list, send a photo from Yucca Valley and we will tell you what we can do.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
Five steps take your hardware from the boat to our bench and back. Here is how a Yucca Valley order goes.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
Pack each piece in its own padding and ship it to Oceanside once you have a quote number, or drop it off during receiving hours.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Most of our boat customers are individual owners, but the same process works for charter captains, marinas, restorers and resorts. Whatever your setup, the steps are the same.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
Keep Your New Finish Looking Sharp
A fresh finish lasts longest with simple habits. Rinse your hardware with fresh water after each trip, dry it with a soft towel and wash with mild soap every few weeks. A marine protectant or wax adds one more layer of defense.
Skip steel wool and harsh rust removers on chrome, since they scratch the surface and can undo the shine. If your boat sits away from the water between trips, rinse and dry the hardware before you cover it.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
Yucca Valley sits well inland from our Oceanside shop, but small and medium hardware ships easily from anywhere. Here is how a mail in order works.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Yucca Valley sits in the high desert, well away from the coast, so boats here often spend time on a trailer or in a driveway between trips. Hardware that bakes in dry heat and then gets wet on a lake or river can still pit and peel. When you are ready, you can ship from Yucca Valley or drive to our Oceanside shop and drop pieces off.
Boat owners in these nearby cities can follow the same steps. Pick the page closest to you.
Frequently Asked Questions
Short answers about cost, timing and corrosion, plus two questions that come up for owners around Yucca Valley.
Yes. Our Oceanside shop takes drop offs during receiving hours, Monday through Friday, 8:00 AM to 4:00 PM Pacific. Send photos first and wait for your quote number so we know to expect you.
It depends mostly on the condition of each piece, then on its size, the metal and how many pieces you send. Sets usually cost less per piece. We give a free written quote from photos, so you know the price before anything ships.
Not for the work itself. We judge hardware by the condition of the plating and the metal, not by where you live. Pits and flaking chrome look the same whether the boat sits on a trailer in Yucca Valley or in a slip.
Most of the time, yes. Green bronze can usually be saved unless corrosion has cracked the casting or eaten through it. We clean it back to solid metal, fill pits with copper and replate with nickel and chrome.
Most projects take 3 to 5 weeks. If you are up against a deadline, expedited orders run 5 to 7 business days, as availability allows. Ask about timing when you send your photos.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.