Railings and Gates
Wrought iron and steel railings, gate panels and balusters stripped of rust and flaking paint, then powder coated or plated to stand up to weather again.
Our shop handles stripping, repair, plating, powder coating and polishing under one roof. If you are in Villa Park, you get honest advice on the right finish before any work begins.
Honest advice before you spend a dollar
Matching is harder than it sounds. One refinished chair in Villa Park is easy. Eight chairs, a pair of gates and a set of light fixtures that all need to look like they belong together takes planning, and that is work we do well.
At Decorative Metal Coatings in Oceanside, California, pieces from the same set are refinished together so the color and finish stay consistent. We have been doing this for businesses and homeowners for over 35 years.
Property managers and homeowners around Orange, Anaheim and Tustin can send photos of the full set and we will quote it as one job.
Start with a few photos. Tell us what the piece is, where it lives and how you want it to look, and we will explain what it needs, what it will cost and how long it will take before anything leaves your hands.
Not sure whether your piece qualifies? These examples show what we refurbish for anyone in Villa Park or anywhere else.
Wrought iron and steel railings, gate panels and balusters stripped of rust and flaking paint, then powder coated or plated to stand up to weather again.
Chandeliers, sconces, lamp bases and stands taken apart, cleaned, refinished arm by arm and returned ready for your electrician to rewire.
Outdoor sculptures, fountains and birdbaths cleaned of corrosion and mineral stains, repatinated or sealed so they age gracefully instead of falling apart.
Cabinet pulls, drawer handles and decorative knobs restored with a durable finish that brings back their original beauty, with options ranging from classic designs to modern styles.
Antique hardware, candlesticks, clocks and keepsakes handled with care, cleaned and refinished while engraving, stamps and fine detail are preserved.
Dedication plaques, address numbers, metal signs and wall art brought back to crisp, readable condition with lettering and relief kept sharp.
Five steps take you from the first photo to a finished piece. You see a written quote before anything ships or changes hands.
Show us the whole piece and any close ups of rust, breaks or missing parts, plus rough dimensions.
We identify the metal and its condition, suggest the best finish and send a written quote within 24 business hours.
Take it to our Oceanside shop yourself, or box it with padding and ship it. Gates, railings and furniture should be crated or palletized.
Old coatings and rust come off, bends are straightened, pits are filled and the surface is polished or blasted.
The new finish is applied, every detail is checked and the piece is packed and returned insured.
The right finish depends on where the piece lives and how it is used. We help you choose before any work begins.
Drag the handle on any photo to see the piece as it came in and as it went home.
Before
Blackened brass with flaking lacquer on every arm. Taken apart, stripped, polished and refinished in bright brass, then sealed so the shine lasts.
Before
Years of rust, chipped paint and weather exposure. Stripped down to bare metal, restored and finished with a durable matte black coating built for long-lasting performance.
Before
Green corrosion hid most of the lettering. Cleaned, given a new dark patina, raised letters polished bright and sealed against the weather.
Over three decades of plating, one shop in Oceanside.
Every part is stripped, prepped, plated and inspected in our own building, and our work comes with a 12 month workmanship guarantee. Send photos and we'll take it from there.
Each metal ages in its own way, so each one needs its own cleaning, repair and finish.
Rust is removed down to clean metal and any weak spots are checked before a protective finish goes on. Powder coat or plating both work well.
Tarnish and old lacquer are stripped so the metal can be polished, replated or given a new patina, depending on the look you want.
Light and corrosion resistant, but chalky and pitted with age. Cleaned and refinished in powder coat or plated after the right pretreatment.
Copper pieces can be polished bright and sealed, or cleaned and darkened to an even antique tone that hides fingerprints.
Common in old lamps and fixtures. Fragile and porous, so we strip it gently and fill pits by hand. Slow work that many shops turn down.
Pieces with glass, wood, stone or old paint attached are reviewed case by case. Send photos and we will explain what can be removed safely.
The pieces, finishes and repair work that make up a typical refurbishing job in our shop.
Since 1989 we have been rescuing metal pieces that other people gave up on. Homeowners, designers, collectors and businesses trust us because every finish we offer is done in house, so the advice we give is about your piece, not our shortcuts.
Send a photo of your part and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
One heirloom or a full set of furniture, shipped to us from any state and returned insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Large sets, small keepsakes and everything in between, these are the customers we serve.
Brass rails, slot trim, light fixtures, signage and decorative metal refreshed between renovations, often in large matched sets. Trusted by casino resorts across North County San Diego.
Bar stools, patio sets, railings and lobby fixtures restored for a fraction of the cost of replacing a whole room.
Family heirlooms, entry gates, light fixtures and garden pieces brought back so they can stay in the home.
Entry gates, pool fencing panels, mailboxes and address signs refinished to keep a community looking cared for.
Salvaged and vintage metal reworked in a new finish to fit a modern design, matched across every room of a project.
Careful cleaning and refinishing that respects age and value, with the option to keep original patina where it matters.
Every piece that comes through our door has a story. Our job is to give it a better next chapter, not to erase what made it worth saving.
If a piece is not worth refurbishing, or needs work outside what we do, we tell you before you spend a dollar.
Engraving, castings, stamps and maker marks are protected during stripping and polishing so the character of the piece survives.
Outdoor pieces get finishes built for sun and salt air, indoor pieces get finishes chosen for looks and easy care.
Every refurbished piece is wrapped, padded and boxed with care, and large items are crated when needed.
Keep it, fix it or let it go
Ask whether a new version would be built the same way. Many mass produced items use thinner metal and lighter coatings, and a refurbished older piece often outlasts them.
Then consider the details. Engraving, scrollwork and maker marks are hard to find on new items, and we protect them while we strip and polish so they stay on the finished piece.
Then think about what the piece means and what it would cost to replace with the same quality. Vintage lighting, cast garden pieces, ornamental iron and antique hardware are rarely made the same way anymore. Refurbishing often costs less than a new item of equal build, and the result is one of a kind.
Finally, consider where it will live. A piece moving from indoors to a patio may need a different finish than it had before. Tell us its new home and we will choose a finish that will hold up there.
Metal Finishing Gallery
A look at recent work from our Oceanside shop: plated hardware, lighting, hospitality and casino pieces, marine fittings and industrial parts.
Whether you drive a piece in from Villa Park or ship it, the preparation is the same.
Send photos of each piece with rough dimensions and the finish you have in mind. You receive a written quote and lead time, usually the same business day. Always wait for a quote number before shipping.
Wrap small pieces individually with at least three inches of padding. Remove glass shades and crystals from fixtures and pack them separately. Gates, railings and furniture should be crated or palletized.
Declare the real value with the carrier and email us the tracking number so we can log your pieces the day they arrive.
When the work is done we photograph the finished pieces for your approval, then pack them in fresh materials and ship them back insured.
Every refurbishing job is stripped, repaired, refinished and inspected in our own facility in North County San Diego.
Metal refurbishing, plating, powder coating and patinas in San Diego County since 1989.
Villa Park is a small, mostly residential city in Orange County, with large lots and many custom homes. Entry gates, lanterns, door hardware and light fixtures are the pieces that show wear first. Matching them across a whole house takes planning, so we refinish related pieces together to keep the color and sheen the same.
Villa Park has neighbors like Orange, Anaheim and Tustin, and each of them follows the same simple process with us. Neighboring cities with their own pages are linked below.
Frequently Asked Questions
We put the most helpful answers here. For anything else, send us a message with your photos.
Yes. Send photos of everything that should match, and tell us which room or part of the house each piece comes from. We refinish them together so the color and sheen come out even from one piece to the next.
Yes. We clean off corrosion and mineral stains, then repatinate or seal the bronze so it ages gracefully. We can also keep the original tone if you prefer. Send photos of the whole piece and close ups of the problem areas.
There is a wide range of colors and textures, from satin black to bright shades. Send a sample or tell us the look you want, and we will recommend a color that suits the piece and where it will be used.
Our refurbishing page shows before and after photos of finished work, including a brass chandelier, wrought iron door pulls and a bronze plaque. Ask us if you want to see something closer to your piece.
Bring your quote number, a list of every piece and the finish for each, and any loose screws or parts in a labeled bag. Add your name, phone number and email on a printed sheet.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.