Bright Copper
A deep, mirror polished copper finish for lighting, hardware and decorative pieces, sealed with a clear coat so the color stays rich instead of darkening.
Copper Plating in Upland, CA
Copper plating in Upland for owners of Craftsman and Spanish revival homes, shops in the downtown district on Second Avenue and families up in San Antonio Heights. Pack your hardware or lighting, ship it to our Oceanside shop, and we'll refinish it in copper and insure the return.
Certified, Approved and Verified
Copper Plating Services in Upland
Euclid Avenue and old citrus money.
Upland's Euclid Avenue runs uphill with a wide planted median, and the Madonna of the Trail monument has stood on it since the 1920s. Citrus built the town, and its historic downtown and older neighborhoods still hold Craftsman bungalows and Spanish revival homes with original metal on doors, porches and cabinets.
The final finish is only as good as the hours before it. A Craftsman hinge with three coats of paint and a century of polish needs stripping, careful buffing so the edges stay square and a deep clean in a hot bath. Rush any of that and the copper shows every shortcut.
San Antonio Heights sits higher, with larger lots, rustic homes and more weather. Lanterns and gate hardware from up there need more rust work before plating.
Tell us what the part is and what you want it to become. Send a few photos and the base metal if you know it, and we will recommend the right copper process, explain the preparation it needs and send back a written quote.
What We Do
Copper Plating Services
A Craftsman house usually calls for antique copper, a remodeled kitchen for satin and decor for bright. You choose a clear coat or natural aging. On industrial parts, copper fills fine scratches before nickel goes on.
Satin Copper
A brushed, low glare copper with a soft grain. It hides fingerprints and light wear, a favorite for door hardware, cabinet pulls and interior trim.
Antique Copper
Copper that is darkened and then relieved by hand, so the high points glow while recesses stay deep brown. Ideal for period restorations and rustic designs.
Copper Buff Base
A heavy acid copper layer that is cut and buffed flat before nickel and chrome. It fills pits and polishing marks and is the foundation of every show chrome job.
Copper Strike
A thin first layer that locks onto difficult metals like zinc die cast, steel and brass, giving every layer that follows a solid bond.
Industrial Copper
Functional copper for conductivity, solderability and heat treat masking. Plated to a specified thickness on bus bars, connectors, shafts and gears.
Restoration Results
Before and After
Drag the handle on any photo to see the part as it arrived and as it left the shop in copper.
Before
Vintage Table Lamp
Worn, spotted brass with decades of tarnish. Stripped, polished and plated in bright copper, then sealed with a clear lacquer so the warm color stays put.
BRIGHT COPPER
BRASS
LACQUERED
Before
Antique Door Hardware
A full set of levers, plates and hinges with peeling plating. Stripped, copper plated and hand antiqued so the raised details stand out against darker recesses.
ANTIQUE COPPER
STEEL
SET MATCH
Before
Copper Base for Chrome
Pitted metal with failed chrome. Stripped down, built up in heavy acid copper, then cut and buffed flat to create a perfect base for nickel and chrome.
COPPER BUFF BASE
STEEL
SHOW CHROME PREP
Ship It From Anywhere
You don't have to live nearby to work with us.
Customers all over the country pack their parts and ship them to our Oceanside shop. We finish them, inspect them and send them back insured. It starts with a few photos.
What We Can Finish
Metals We Copper Plate
Copper bonds to more base metals than almost any other plating, but each one still needs the right cleaning and the right first layer.
Steel
Cleaned and activated, then given a copper strike before the main copper layer. Rusted or pitted steel is stripped and copper filled until the surface is smooth.
Brass and Bronze
Plate beautifully once cleaned. A common way to give brass lighting, hardware and fixtures a true copper color without replacing the part.
Zinc Die Cast and Pot Metal
Porous and reactive, so it needs a gentle copper strike before anything else. Pits are copper filled and hand buffed flat, the slow work most shops avoid.
Aluminum
Receives a zincate pretreatment so copper can bond to a surface that would otherwise oxidize instantly. Used for wheels, housings and decorative castings.
Stainless Steel
Its oxide layer resists bonding, so it gets a nickel strike first. After that it takes copper like any other metal, for a warm look on a durable base.
Copper and Specialty Alloys
Solid copper can be replated to restore its surface, and other alloys are reviewed case by case. Send the alloy or a photo and we will confirm before you ship.
Choosing the Right Copper
Three Ways We Use Copper
The same metal, three different goals. Knowing which one your part needs decides how it is prepared, how thick the copper goes on and how it is finished.
Copper as the Finish
- Bright, satin or antique look
- Sealed with clear lacquer
- Lighting, hardware and decor
- Color matched to a sample
- Judged by appearance
Copper Under Chrome
- Heavy layer, buffed flat
- Fills pits and polishing marks
- Covered by nickel and chrome
- Bumpers, trim and wheels
- Judged by the final chrome
Functional Copper
- Conductivity and solderability
- Heat treat stop off masking
- Plated to a set thickness
- Bus bars, contacts, gears
- Judged by spec and coverage
How It Works
Our Copper Plating Process
Photos by email, a line about the look, and we write back with a no obligation price.
1
Send Photos
Show us the part and tell us the finish you want: bright, satin, antique or a base for chrome.
2
Get Your Quote
We confirm the base metal and the prep it needs, then send a written quote within 24 business hours.
3
Ship or Drop Off
Paint on old Upland hardware often fills screw slots and hinge knuckles. We open those up, strip in stages and square the edges back up on the wheel before the strike.
4
Strip, Strike and Plate
Old finishes come off, the surface is repaired and polished, then struck and plated in copper.
5
Finish and Seal
Parts are buffed, brushed or antiqued, sealed when needed, inspected and shipped back insured.
Copper Plating Catalog
Copper Finishes and Services
Every copper finish and copper related service we run in house.
Decorative Copper
- Bright Copper
- Polished Copper
- Satin Copper
- Brushed Copper
- Antique Copper
- Oil Rubbed Copper
- Clear Lacquer Topcoat
Underlayer and Industrial
- Copper Buff Base for Chrome
- Acid Copper Leveling Layer
- Copper Strike
- Conductive Copper
- Copper for Soldering
- Heat Treat Stop Off Copper
Base Metals and Prep
- Steel
- Stainless Steel
- Brass and Bronze
- Zinc Die Cast
- Aluminum (Zincate)
- Stripping and Replating
- Masking for Selective Plating
- Custom Sample Match
What Our Clients Say
Trusted by Professionals
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Who We Serve
Who Relies on Our Copper
We plate for old house owners, restorers, downtown restaurants and shops, foothill properties and landlords. One hinge or a whole house.
Casinos and Gaming
Slot machine trim, table rails, bar fixtures and gaming floor accents in bright or antique copper, made to glow under bright lights around the clock. Trusted by casino resorts across North County San Diego.
Lighting and Decor
Pendants, sconces, lamp bases and accessories finished in bright, satin or antique copper.
Architectural Hardware
Door handles, hinges, cabinet pulls and railings given a warm copper finish that matches across a project.
Hospitality
Bar rails, foot rests, tap handles and restaurant fixtures that bring copper warmth to a space.
Electrical Components
Bus bars, terminals and connectors plated for conductivity and easy soldering.
Manufacturing and Heat Treat
Gears, shafts and steel parts selectively copper plated to mask areas during carburizing.
35+
Years of Expertise
Take a Moment to Learn More
About Decorative Metal Coatings
We have been running copper tanks since 1989. Restorers, designers, builders and manufacturers send us parts because the copper work underneath is what makes the finish on top last.
Free Estimates Available
Send a photo of your part and receive a no obligation quote within 24 hours.
Quality Guaranteed
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Ship From Anywhere in the US
A single fixture or a full production run, shipped to us from any state and returned insured.
Fast Turnaround Times
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Our Commitment
Copper Done the Right Way
Copper shows everything. Every scratch left in the base metal and every shortcut in the prep ends up visible in the finish, so we do not take shortcuts.
Proper Strike Layer
Difficult metals get the right first layer before the main copper goes on, so the finish stays bonded and does not peel or blister.
Hand Buffed
Copper is cut and buffed by hand between stages, which is what gives decorative copper its depth and chrome its flawless base.
Color Checked
Finished copper is inspected for even color, gloss and texture, and matched to your sample when you send one.
Packed to Protect
Soft copper scratches easily, so every finished piece is wrapped separately and packed to arrive exactly as it left the shop.
What We Do Differently
- We confirm the base metal before choosing the copper process
- Old plating is stripped instead of covered over
- Decorative copper is sealed so the color lasts
- We send photos when a part needs a decision from you
- Every order is inspected before it is packed
What You May Experience Elsewhere
- Copper plated straight over old, failing finishes
- No strike layer, leading to peeling and blistering
- Unsealed copper that turns brown within weeks
- Polishing marks left visible under the finish
- Little communication once parts are in the shop
Copper Care in Upland
Mountain views and dry summer air.
Upland summers are hot and dry, and winter nights turn cold with snow on the peaks. Sealed copper inside the house holds its color through all of it. A soft cloth, warm water and mild soap clean it, and a towel dries it.
Porch copper left bare on a bungalow darkens to a deep brown that suits the style. Gate pieces up in the Heights may green a little where sprinklers reach. Seal them if you'd rather they stay bright.
If you prefer a living finish, we can leave the copper unsealed so it develops its own patina over time. That choice works well on rustic lighting, garden pieces and bar tops where the aging is part of the character.
When a lacquered piece starts to show dark spots, the coating has failed somewhere. Bring it back and we can strip the old lacquer, rebuff the copper and seal it again, usually without replating the whole part.
Project Gallery
Copper Plating Gallery
Bright, satin and antique copper on lighting, hardware and hospitality pieces, plus functional copper for electrical and industrial work.
Nationwide Service
Ship Us Your Parts From Anywhere in the US
Wrap hinges in pairs, keep each door's screws together and mark which room they came from.
01
Quote before you ship
Send photos of every piece and the copper finish you want. You receive a written quote and lead time, usually the same business day. Always wait for a quote number before shipping.
02
Wrap every piece on its own
Wrap each part individually so metal never touches metal, and use at least three inches of padding on every side. Long trim and lighting arms should be double boxed.
03
Insure it and share tracking
Declare the real value with the carrier and email us the tracking number so we can log your parts the day they arrive.
04
Inspected, then shipped back
When the copper work is done we photograph the finished pieces for your approval, then pack them in fresh materials and ship them back insured.
Visit Us
Our Location
Every copper job is stripped, plated, buffed and inspected in our own facility in North County San Diego.
Decorative Metal Coatings
Copper, nickel, chrome and metal finishing in San Diego County since 1989.
- Address 2613 Temple Heights Dr, Ste G, Oceanside, CA 92056
- Phone (760) 746 3378
- Quotes Send photos and get a price
Business Hours
- Monday to Friday 8:00 AM to 5:00 PM
- Saturday 9:00 AM to 2:00 PM
- Sunday Closed
Shipping from Upland
A box sent by ground from Upland normally reaches our shop after 1 business day, and the finished hardware returns insured.
Nearby Cities We Serve
Upland's west valley neighbors send copper work too:
Copper Plating Near Me in Upland
Frequently Asked Questions
Upland homeowners restoring older houses often ask us about these things.
Yes. Paint removal is part of our prep. We strip in stages so the brass or iron underneath isn't damaged, open up filled screw slots and clean the knuckles. Most painted hinges come out in better shape than owners expect.
Old pieces carry paint, polish, grime and sometimes rust, all of which must come off for copper to bond. Edges also need careful buffing to stay square. That work takes more time than plating, and it's what makes the finish last.
It's a classic match. Antique copper suits the wood, earthy colors and simple lines of Craftsman homes. It looks like it has always been there and hides fingerprints on doors and cabinets. Many restorers choose it for every room.
Yes. Gate hardware up there is usually iron or steel with some rust. We remove the rust, buff the metal and add a strike layer, then plate copper. Lacquer helps it hold up to mountain weather and sprinklers.
Not noticeably. The copper layer is very thin, so hinges and knobs fit the same doors. If a piece was painted heavily before, it may actually fit better once that paint is gone and the metal is back to its true size.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.