Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
From Valencia to Santa Clarita and beyond, zinc die cast pieces can ship to our Oceanside shop and come back finished. We run a sample first, then the full batch, and your die cast pieces return insured and packed by part number.
Finishing metal since 1989, with zinc die cast pieces in mind
You don't need to bring parts to Oceanside. Most tumbling work reaches us by mail, and the process is easy to follow, step by step. Start with photos, the metal type, a part count and the finish you want. We send a written quote and a quote number, and you ship once you have it.
For parts leaving Santa Clarita, bag each part number separately and label the bags. Pack the box tight, because small metal parts are heavy and they shift in transit. Insure the box for its real value and email us the tracking number.
On our end, parts get sorted, sampled, tumbled, dried and checked. Then they're packed by part number and sent back insured. The steps are the same from Valencia, Castaic or Newhall as they are from Santa Clarita.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Whatever the metal, we match the finish to the job, from zinc die cast pieces to anything in between. Die cast pieces sent from Santa Clarita might need burrs removed, edges rounded, a bright burnished shine or smooth edges with the detail left intact.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Getting smooth edges with the detail left intact on zinc die cast pieces takes six steps, and you only handle the first two.
Tell us what the parts are, how many you have and the finish you are after.
After your quote is approved, mail your zinc die cast pieces from Santa Clarita to our shop in Oceanside, California. Keep part numbers in separate bags and call first if you're sending a pallet of die cast pieces.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Casinos, machine shops, furniture makers and small brands all rely on tumbled metal, including zinc die cast pieces. Here's who we finish for, and where die cast pieces tend to fit in.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
A few details now save time on your zinc die cast pieces later
Write down any holes, slots or threads on your zinc die cast pieces. Media can wedge into openings close to its own size, so we pick a shape and size that stays clear of the openings on die cast pieces, and we check every finished piece for anything stuck.
If any of your zinc die cast pieces have a thread or a tight fit that has to stay exact, mention it when you ask for a quote from Santa Clarita. Tumbling takes very little metal off die cast pieces, but we'd rather plan for it than guess.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Small metal parts like zinc die cast pieces travel well when they're packed right. Here's how to send a box of die cast pieces from Santa Clarita to our Oceanside shop.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Out in Santa Clarita, in the Santa Clarita Valley north of Los Angeles, you don't have to make the trip. Send photos of your zinc die cast pieces, get a written quote, and ship the box when your quote number comes through. Newhall works the same way.
Other cities around Santa Clarita and Valencia that we serve by mail are listed below.
Frequently Asked Questions
Most questions about tumbling zinc die cast pieces come down to a few themes. Here are the ones that matter most for die cast pieces sent from Santa Clarita or Castaic.
Yes. Ask for a quote first with photos of your zinc die cast pieces and a part count, and wait for your quote number before you ship. It lets us match the box to your order and plan the finish for your die cast pieces ahead of time.
We run compounds and water in the tumbler, and spot free drying afterward keeps zinc die cast pieces looking clean. For long term protection of die cast pieces, we can add a clear lacquer, and we'll suggest whether to leave them bare or seal them based on how they'll be used.
Often, yes. Tumbling removes scale, light rust and surface marks, so copper, nickel or chrome goes on your zinc die cast pieces smoother and looks better for less cost. It also rounds sharp edges, which helps plating cover the corners of die cast pieces evenly, and we handle both steps in our shop.
Tumbling shines when you have a few dozen zinc die cast pieces or more, up to full production runs. With a handful of die cast pieces, hand polishing may cost less, and we'll say so honestly once we see your photos and the part count.
Yes, but tell us about them first. Media can wedge into openings close to its own size, so we pick a shape and size that stays clear of the openings on your zinc die cast pieces. Send the hole sizes of your die cast pieces with your photos, and every finished batch is checked for lodged media.
Not at all. Most of what comes through our door is home and business hardware: faucets, light fixtures, door handles, cabinet pulls, railings and decorative pieces. We also work for hotels, restaurants, boat owners and manufacturers.
Tell us what the part is, roughly how big it is, how many pieces you have and the finish you're after. If you know the metal, mention it. If not, that's fine. We can usually tell from the photos.
Every part is quoted on its own. The biggest factors are condition, the base metal, size and shape, the finish you choose and how many pieces you send. A part with deep pits or broken spots takes more work before it can be plated.