Railings and Gates
Wrought iron and steel railings, gate panels and balusters stripped of rust and flaking paint, then powder coated or plated to stand up to weather again.
Chandeliers, sculptures, railings, hardware and keepsakes all come through our shop. If you are in San Juan Capistrano, you can start with photos, get a written quote and decide with no pressure.
Protecting the detail that makes a piece yours
Decorative Metal Coatings in Oceanside, California has restored metal for over three decades. Homeowners, designers, collectors and property managers send us railings, lamp bases, patio sets, old brass and garden pieces, and a piece from San Juan Capistrano is welcome like any other.
We do not do quick and cheap. Rust and old paint come off completely, bent parts are straightened, pits are filled and the surface is prepped by hand before anything new goes on. That prep is where a refinish either lasts or fails, so it is where we spend our time.
If you are near Dana Point or San Clemente, or anywhere around Laguna Niguel, the first step costs nothing. Send a few photos and we will tell you what we would do, what it would cost and how long it should take.
Start with a few photos. Tell us what the piece is, where it lives and how you want it to look, and we will explain what it needs, what it will cost and how long it will take before anything leaves your hands.
If you are in San Juan Capistrano and wondering what we can handle, this is a look at the pieces that come through our shop most.
Wrought iron and steel railings, gate panels and balusters stripped of rust and flaking paint, then powder coated or plated to stand up to weather again.
Chandeliers, sconces, lamp bases and stands taken apart, cleaned, refinished arm by arm and returned ready for your electrician to rewire.
Outdoor sculptures, fountains and birdbaths cleaned of corrosion and mineral stains, repatinated or sealed so they age gracefully instead of falling apart.
Cabinet pulls, drawer handles and decorative knobs restored with a durable finish that brings back their original beauty, with options ranging from classic designs to modern styles.
Antique hardware, candlesticks, clocks and keepsakes handled with care, cleaned and refinished while engraving, stamps and fine detail are preserved.
Dedication plaques, address numbers, metal signs and wall art brought back to crisp, readable condition with lettering and relief kept sharp.
Every job follows the same five steps, whether it is one lamp or a full set of railings.
Show us the whole piece and any close ups of rust, breaks or missing parts, plus rough dimensions.
We identify the metal and its condition, suggest the best finish and send a written quote within 24 business hours.
Drop it off in Oceanside or send it by carrier. If it is a big piece, tell us and we will plan the delivery with you.
Old coatings and rust come off, bends are straightened, pits are filled and the surface is polished or blasted.
The new finish is applied, every detail is checked and the piece is packed and returned insured.
The right finish depends on where the piece lives and how it is used. We help you choose before any work begins.
Drag the handle on any photo to see the piece as it came in and as it went home.
Before
Blackened brass with flaking lacquer on every arm. Taken apart, stripped, polished and refinished in bright brass, then sealed so the shine lasts.
Before
Years of rust, chipped paint and weather exposure. Stripped down to bare metal, restored and finished with a durable matte black coating built for long-lasting performance.
Before
Green corrosion hid most of the lettering. Cleaned, given a new dark patina, raised letters polished bright and sealed against the weather.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
Each metal ages in its own way, so each one needs its own cleaning, repair and finish.
Rust is removed down to clean metal and any weak spots are checked before a protective finish goes on. Powder coat or plating both work well.
Tarnish and old lacquer are stripped so the metal can be polished, replated or given a new patina, depending on the look you want.
Light and corrosion resistant, but chalky and pitted with age. Cleaned and refinished in powder coat or plated after the right pretreatment.
Copper pieces can be polished bright and sealed, or cleaned and darkened to an even antique tone that hides fingerprints.
Common in old lamps and fixtures. Fragile and porous, so we strip it gently and fill pits by hand. Slow work that many shops turn down.
Pieces with glass, wood, stone or old paint attached are reviewed case by case. Send photos and we will explain what can be removed safely.
The pieces, finishes and repair work that make up a typical refurbishing job in our shop.
Since 1989 we have been rescuing metal pieces that other people gave up on. Homeowners, designers, collectors and businesses trust us because every finish we offer is done in house, so the advice we give is about your piece, not our shortcuts.
Send a photo of your part and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
One heirloom or a full set of furniture, shipped to us from any state and returned insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Whether you are a homeowner in San Juan Capistrano or a business with many pieces, the process works the same way.
Brass rails, slot trim, light fixtures, signage and decorative metal refreshed between renovations, often in large matched sets. Trusted by casino resorts across North County San Diego.
Bar stools, patio sets, railings and lobby fixtures restored for a fraction of the cost of replacing a whole room.
Family heirlooms, entry gates, light fixtures and garden pieces brought back so they can stay in the home.
Entry gates, pool fencing panels, mailboxes and address signs refinished to keep a community looking cared for.
Salvaged and vintage metal reworked in a new finish to fit a modern design, matched across every room of a project.
Careful cleaning and refinishing that respects age and value, with the option to keep original patina where it matters.
Every piece that comes through our door has a story. Our job is to give it a better next chapter, not to erase what made it worth saving.
If a piece is not worth refurbishing, or needs work outside what we do, we tell you before you spend a dollar.
Engraving, castings, stamps and maker marks are protected during stripping and polishing so the character of the piece survives.
Outdoor pieces get finishes built for sun and salt air, indoor pieces get finishes chosen for looks and easy care.
Every refurbished piece is wrapped, padded and boxed with care, and large items are crated when needed.
What to check before you buy new
Look at what the finish is doing now. Bubbling, flaking or a dull, spotted surface tells us the coating has failed, and that is usually a fixable problem, whatever the metal underneath looks like.
We strip the old coating all the way off rather than painting over it. That is the difference between a finish that lasts and one that bubbles through within a season.
Then think about what the piece means and what it would cost to replace with the same quality. Vintage lighting, cast garden pieces, ornamental iron and antique hardware are rarely made the same way anymore. Refurbishing often costs less than a new item of equal build, and the result is one of a kind.
Finally, consider where it will live. A piece moving from indoors to a patio may need a different finish than it had before. Tell us its new home and we will choose a finish that will hold up there.
Metal Finishing Gallery
A look at recent work from our Oceanside shop: plated hardware, lighting, hospitality and casino pieces, marine fittings and industrial parts.
If you are in San Juan Capistrano, you can bring a piece to Oceanside or ship it. Either way, the quote comes first.
Send photos of each piece with rough dimensions and the finish you have in mind. You receive a written quote and lead time, usually the same business day. Always wait for a quote number before shipping.
Wrap small pieces individually with at least three inches of padding. Remove glass shades and crystals from fixtures and pack them separately. Gates, railings and furniture should be crated or palletized.
Declare the real value with the carrier and email us the tracking number so we can log your pieces the day they arrive.
When the work is done we photograph the finished pieces for your approval, then pack them in fresh materials and ship them back insured.
Every refurbishing job is stripped, repaired, refinished and inspected in our own facility in North County San Diego.
Metal refurbishing, plating, powder coating and patinas in San Diego County since 1989.
San Juan Capistrano is known for its historic mission and the Spanish style architecture around it, which brings plenty of wrought iron gates, lanterns, railings and patio furniture. Coastal moisture and sun wear on all of it. We remove rust, protect fine detail and refinish iron in powder coat or a dark patina that suits older styles.
If you are in Dana Point, San Clemente or Laguna Niguel, the steps are the same as for San Juan Capistrano. If a nearby city is listed below, its page has details of its own.
Frequently Asked Questions
Here is what usually comes up first. Anything else, just ask.
Yes. We strip rust and old paint, repair bent or loose parts and refinish the iron in powder coat or a dark patina. Scrollwork and fine detail are protected, so the pattern stays crisp. Send photos and we will recommend a finish.
We can match a sample. Set and color matching is part of the work, so send a photo of the piece you want to match, or a small sample, and we will recommend a finish that sits well beside it.
Yes. Call us at (760) 746 3378 or send photos first. We can quote most pieces from pictures, which saves a trip, and we will tell you when it is worth stopping by.
Wrap it in blankets or thick padding and keep it from sliding in the vehicle. Remove glass shades and crystals and bring any loose screws in a labeled bag. For delicate items, ask us for packing tips first.
Brass can be polished bright, replated, given a new patina or sealed with a clear coat, depending on the look you want. We strip tarnish and old lacquer first, then recommend a finish for where the piece will live.
Yes, and most of our work starts that way. We strip the old plating down to the base metal, repair what needs repair, then plate it fresh. New plating over a failing layer never lasts, so we don't do it.
We do. Along with single pieces for homeowners, we run batches of hundreds or thousands of parts for companies in California and other states. Send a photo of a sample, the quantity and the finish, and we'll quote the whole run.
Steel, stainless steel, aluminum, brass, bronze, copper, pot metal and zamak. Some of them need extra prep so the plating bonds well, and we'll tell you up front if your part does.