Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Our tumblers finish small bronze and copper castings for decor and restoration work. Bronze and copper castings shipped from San Jose get the right media for the metal, a careful rinse and dry, and a check for stuck media before they're packed and sent back.
Why small bronze and copper castings go home looking better
Our tumbling work runs from a few dozen pieces up to full production runs. That range is wide on purpose, because not everyone who needs tumbling has a thousand parts, and not everyone has a dozen. Either way, the same care goes into your batch.
A few dozen brass pulls need the same care as a few thousand machined fittings, just in a different drum. And if you only have a handful of pieces, we'll tell you so. Hand polishing can cost less in that case, and we'd rather point you there than take your money for the wrong job.
Send photos and a part count and we'll suggest the best way to go, whether you're in San Jose, Santa Clara or Campbell. The quote is free and in writing, so you can take your time and compare it with anything else you're considering.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Tumbling does more than one job. For small bronze and copper castings it can clean, smooth, brighten or age the metal, and we pick the treatment that gets you a warm, even tone.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Six steps take your small bronze and copper castings from a box in San Jose to a finished batch coming back to your door.
Tell us what the parts are, how many you have and the finish you are after.
Ship from San Jose or Santa Clara the same way: strong box, labeled bags, a printed sheet with your quote number and part numbers, and insurance for the full value of the small bronze and copper castings.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
A lot of different trades use tumbled parts, and small bronze and copper castings turn up in many of them. If yours isn't listed here, send photos of your bronze and copper castings anyway and we'll tell you if tumbling suits them.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Before you ship small bronze and copper castings, a few simple things
Samples are the best way to avoid surprises with small bronze and copper castings. If you can include one or two extra pieces in the box from San Jose, we can use them to test a warm, even tone before the full batch of bronze and copper castings runs.
If you already have a piece with the look you want, send that along with the small bronze and copper castings. Matching a finish by eye is easy when we can hold the real thing next to your bronze and copper castings in the drum, and it keeps everyone on the same page.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Shipping small bronze and copper castings to us from San Jose is easy once you know the steps. Follow these four and your bronze and copper castings will arrive ready to run.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Located in the Santa Clara Valley at the south end of San Francisco Bay, San Jose is far enough from Oceanside that mail is the way to go. Request a quote, wait for the quote number, then ship the small bronze and copper castings. Santa Clara and Campbell follow the same steps.
Browse tumble finishing pages for more places near San Jose, Campbell and the towns around them.
Frequently Asked Questions
Short answers first, details second, for small bronze and copper castings. Use these to plan a batch of bronze and copper castings from San Jose, and call if you'd like to talk it through.
Start by emailing photos of your small bronze and copper castings, the metal type and a part count. We send a written quote and a quote number for your bronze and copper castings. Then bag each part number of bronze and copper castings, pack a strong box, insure it and ship it to Oceanside, with the tracking number emailed to us.
Not at all. San Jose is in the Santa Clara Valley at the south end of San Francisco Bay, and batch work doesn't need you nearby. Your small bronze and copper castings ship to Oceanside in a strong box, and the finished parts come back insured and packed by part number.
We choose by metal. Ceramic cuts fast on hard metals, plastic is gentler on brass, aluminum and zinc, porcelain leaves a fine smooth surface, and stainless steel shapes burnish, so we match the media to your small bronze and copper castings. For bronze and copper castings, walnut shell and corn cob handle dry finishing and drying when it's needed.
Yes. Hard and soft parts never share a load, and each part number of small bronze and copper castings is run, bagged and labeled on its own. When the batch is done, your bronze and copper castings are packed by part number and shipped back insured.
Yes, when the media fits the metal. Soft metals like aluminum, zinc and brass run with lighter media and shorter cycles so details and dimensions on small bronze and copper castings are protected. We keep hard and soft parts in separate loads, because heavy pieces can ding and scratch softer bronze and copper castings.
The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.
Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.
When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.