Mirror Polishing
Our brightest finish. The surface is cut, buffed and colored until it reflects like glass, perfect for lighting, display pieces and decorative hardware.
Metal does not have to look worn out. Our polishers cut out scratches, remove tarnish and old lacquer and finish each piece with a color buff. Send a photo from San Bernardino to get started, and we handle the rest from our Oceanside polishing room.
San Bernardino hardware, restored to a clean shine
Think of polishing as a reset button for metal. Tarnish, haze, scratches and worn lacquer come off, and the metal underneath gets to shine again. It is a good deal when the piece is solid and the damage sits on the surface.
Our shop in Oceanside has been resetting metal since 1989, using coarse to fine wheels, the right compound for each metal and a careful color buff to finish. Pieces from San Bernardino, Colton and Highland get the same treatment as any other.
If we think plating would serve you better, we say that too. Sometimes the honest answer is a polish, sometimes a replate and sometimes a bit of both. Photos let us tell the difference.
Send us a few photos and tell us how the piece is used. We will tell you whether polishing alone will get you there or whether it needs plating, explain what finish makes sense and send back a written quote.
Every finish below is cut, buffed and colored in our own shop, not sent out. Choose the one that fits how your piece is used, and ask us if you are not sure which that is.
Our brightest finish. The surface is cut, buffed and colored until it reflects like glass, perfect for lighting, display pieces and decorative hardware.
A fine, even grain that softens glare and hides fingerprints. A smart choice for handrails, pulls and levers that get touched all day long.
Deep scratches, light pitting and tool marks are worked out wheel by wheel, so the finished surface is smooth and even instead of wavy.
Tarnish and old lacquer come off, the metal is brought back to its warm color and sealed with a clear coat if you want it to stay that way.
Each metal needs its own compounds. We polish stainless to a crisp shine and aluminum to a bright finish without burning or smearing the surface.
Plating copies the surface under it. We polish parts flat and clean before nickel, chrome or gold so the final finish comes out flawless.
Drag the handle on any photo to see how the piece arrived and how it looked when it left our polishing room.
Before
Dark tarnish, fingerprint stains and old lacquer flaking at the edges. Stripped, polished to a mirror and sealed with a fresh clear coat.
Before
Years of scuffs from shoes and stools. Scratches were cut out and the rail was brought back to a bright, uniform shine along its full length.
Before
Chalky gray oxidation over every surface. Hand polished into the curves and details until the aluminum showed a clean, bright finish again.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
More shine is not always better. The right level depends on how the piece is used, how often it is touched and the look you want.
Each metal has its own hardness, color and quirks. Knowing them is what keeps a polish from turning out wavy, burned or hazy.
Polish up beautifully and take a deep mirror. Old lacquer is stripped first, then the metal is buffed and resealed so the warm color holds.
Soft and quick to scratch, so it is buffed gently with fine compounds. Finished bright for a classic look or left to age naturally.
Hard and tough to cut, but it holds a polish for years. Ideal for rails, kitchen and bar equipment and marine fittings near the coast.
Turns dull and chalky outdoors. We polish it bright and can seal it to slow the oxidation that brings the haze back.
Polishes well but rusts if left bare, so it usually gets plated or coated after polishing. We will explain the options before we start.
Soft castings with a thin skin. Pushing too hard opens pits, so we polish these by hand with light pressure and know when to stop.
Getting your piece polished is easier than most people expect. Here is how the process goes from start to finish.
Show us the piece, the damage and the look you want: mirror, bright or satin.
We check the metal and the condition, then send a written quote within 24 business hours.
Wrap every piece separately, pad the box with at least three inches on every side and ship it insured, or drop it off at our Oceanside shop. Email us the tracking number and put your quote number inside.
Old lacquer and tarnish come off, then scratches are worked out from coarse to fine wheels.
A final color buff, a full cleaning, an optional clear coat and a close look under bright light.
Sometimes Polishing Is All It Takes
Many customers call asking for plating when their piece only needs a good polish. If the part is solid brass, copper, stainless or aluminum and the damage is on the surface, polishing alone brings it back for less money and keeps the original metal you already like.
Plating is the answer when the color needs to change, when the metal underneath is steel that will rust, or when the old plating has already worn through to a different color. In those cases we still polish first, because a plated finish only looks as good as the surface under it.
Not sure which group your piece falls in? Look at a worn corner or the back side. If the color is the same all the way through, it is probably solid and a polish will do. If you see a different color peeking through, it is plated, and we will talk you through replating.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Every polished finish and restoration service we handle in house.
Polishing wheels have been turning in our shop since 1989. It is the skill every other finish we offer depends on, and the reason homeowners, designers and casino resorts keep sending us their metal.
Send a photo of your piece and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
One heirloom or a full hotel renovation, shipped to us from any state and returned insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Business owners, designers and homeowners in San Bernardino and beyond can all use the same shop. These are the kinds of work we polish.
Slot machine trim, table rails, bar fixtures and decorative accents polished to shine under bright lights day and night. Casino resorts across North County San Diego trust us with their gaming floors.
Bar rails, foot rests, door push plates and lobby fixtures brought back to a bright, welcoming finish.
Door levers, hinges, knobs and railings polished as a matched set so every room looks consistent.
Chandeliers, sconces, lamp bases and decorative pieces polished by hand, curves and details included.
Stainless cleats, rail fittings and bronze hardware cleaned of salt haze and polished to stand up to coastal air.
Family pieces, candlesticks and collectibles polished carefully so engraving, stamps and fine detail stay sharp.
Fast polishing leaves swirls, waves and rounded edges. We take the time each piece needs so the finish looks right from every angle.
Brass, stainless and aluminum each get their own wheels and compounds, so the surface is never burned, smeared or left hazy.
Every grit is fully removed by the next one before we move on. That is how a polish ends up clear instead of swirly.
Finished pieces are cleaned of all compound and inspected under strong light from several angles before they are approved.
A fresh mirror scratches easily, so each piece is wrapped in soft material and boxed to arrive just as it looked in our shop.
Look after it and it looks after you
Most finish problems come from one of three things: scrubbing too hard, mixing cleaners or letting moisture sit. Avoid those and a good finish can last for years. Our guarantee covers the work we do, and our advice is free.
Inland sun fades lacquer over time, so look over sealed pieces once a year for dull or flaking spots. Questions about a specific piece are welcome. Send a photo and we tell you how to look after it.
Unsealed pieces can be kept bright with a gentle metal polish and a clean microfiber cloth. Rub lightly in the direction of the grain on satin finishes, and use a fresh area of the cloth as it picks up black residue. Abrasive pads and kitchen scrubbers will scratch a mirror finish in seconds.
Near the ocean, salt air speeds everything up. Rinse outdoor hardware with fresh water now and then and dry it. When a piece finally loses its shine, send it back. A repolish is usually quick because the hard cutting work was already done the first time.
Metal Finishing Gallery
A look at recent work from our Oceanside shop: plated hardware, lighting, hospitality and casino pieces, marine fittings and industrial parts.
A fresh polish scratches easily, so packing matters in both directions. Here is how to send your pieces safely.
Email photos of each piece, front and back, and the finish you want. You receive a written quote and lead time, usually the same business day. Wait for your quote number before you ship.
Wrap every piece on its own in soft cloth or bubble wrap so nothing rubs together in transit. Pad the box with at least three inches on every side and double box long rails or tubes.
Declare the full value with the carrier and email us the tracking number so we know what is coming and can log it the day it lands.
Once polishing is done we send photos for your approval, then pack your pieces in new materials and return them insured.
Every piece is polished, cleaned and inspected by hand in our own shop in North County San Diego.
Metal polishing, plating and finishing in San Diego County since 1989.
San Bernardino is about an hour and forty minutes inland from our Oceanside shop, at the foot of the mountains. Most customers ship pieces with insurance and tracking, and drop offs work well once you have your quote number.
Pieces from these cities near San Bernardino go through the same steps.
Frequently Asked Questions
Most questions come down to cost, timing and what finish to pick. Here is what we tell people who ask.
Yes. We handle everything from one heirloom to a full hotel renovation, and the process is the same. Send photos, get a free written quote and ship when you have your quote number.
Yes. Chandeliers, sconces and lamp bases are polished by hand, curves and details included. Remove glass, shades and bulbs first, and pack arms and parts separately so nothing rubs together.
Yes. Restaurants, offices and shops can send rails, handles and display fixtures. List every piece with the finish you want and we quote the job as one set so the finish matches.
Heat and dust do wear on bare finishes. A soft cloth, gentle cleaning and a clear coat on brass and copper slow the damage. A repolish clears the haze when the shine fades.
Often yes. Light dents and deep scratches can be worked out before the final polish, but a bent or cracked piece may need repair first. Send photos and tell us what happened, and we let you know what is realistic before you commit.
It depends on the part. Older fixtures and hardware are often better made than what you can buy today, or simply can't be found anymore. Send us photos and we'll give you an honest answer, even if that answer is to buy a new one.
Yes. We work with hotels, casinos, restaurants, architects, contractors and manufacturers, as well as homeowners. For businesses we can plate a whole project to one finish so every piece matches.
Yes. Our shop is at 2613 Temple Heights Dr, Suite G, in Oceanside. Bring your quote number and your parts during business hours, Monday to Friday 8 AM to 5 PM or Saturday 9 AM to 2 PM.