Mirror Polishing
Our brightest finish. The surface is cut, buffed and colored until it reflects like glass, perfect for lighting, display pieces and decorative hardware.
A fresh polish can take years off a piece. We work by hand, one wheel at a time, so the finish comes out smooth and even. Share a few photos from Palm Desert and get a free written quote with a clear turnaround time.
Palm Desert metal, polished the careful way
Not every piece needs a mirror. A satin grain hides fingerprints on a handle, a bright buff gives hardware an easy glow and a full mirror makes lighting and trim stand out. Part of our job is helping you pick the one that fits.
We have polished by hand in Oceanside since 1989, so we have a good sense of what holds up and what shows wear. Tell us how the piece is used and where it lives, and we point you to the finish that makes sense.
Photos from Palm Desert, Indian Wells or La Quinta are all it takes to begin. Send up to five, front and back, and you get a free written quote within 24 business hours.
Send us a few photos and tell us how the piece is used. We will tell you whether polishing alone will get you there or whether it needs plating, explain what finish makes sense and send back a written quote.
We keep the service list simple. Pick a finish, tell us the metal and send photos from Palm Desert. We handle the coarse cutting, the fine buffing and the color work that makes the surface look right.
Our brightest finish. The surface is cut, buffed and colored until it reflects like glass, perfect for lighting, display pieces and decorative hardware.
A fine, even grain that softens glare and hides fingerprints. A smart choice for handrails, pulls and levers that get touched all day long.
Deep scratches, light pitting and tool marks are worked out wheel by wheel, so the finished surface is smooth and even instead of wavy.
Tarnish and old lacquer come off, the metal is brought back to its warm color and sealed with a clear coat if you want it to stay that way.
Each metal needs its own compounds. We polish stainless to a crisp shine and aluminum to a bright finish without burning or smearing the surface.
Plating copies the surface under it. We polish parts flat and clean before nickel, chrome or gold so the final finish comes out flawless.
Drag the handle on any photo to see how the piece arrived and how it looked when it left our polishing room.
Before
Dark tarnish, fingerprint stains and old lacquer flaking at the edges. Stripped, polished to a mirror and sealed with a fresh clear coat.
Before
Years of scuffs from shoes and stools. Scratches were cut out and the rail was brought back to a bright, uniform shine along its full length.
Before
Chalky gray oxidation over every surface. Hand polished into the curves and details until the aluminum showed a clean, bright finish again.
Over three decades of plating, one shop in Oceanside.
Every part is stripped, prepped, plated and inspected in our own building, and our work comes with a 12 month workmanship guarantee. Send photos and we'll take it from there.
More shine is not always better. The right level depends on how the piece is used, how often it is touched and the look you want.
Each metal has its own hardness, color and quirks. Knowing them is what keeps a polish from turning out wavy, burned or hazy.
Polish up beautifully and take a deep mirror. Old lacquer is stripped first, then the metal is buffed and resealed so the warm color holds.
Soft and quick to scratch, so it is buffed gently with fine compounds. Finished bright for a classic look or left to age naturally.
Hard and tough to cut, but it holds a polish for years. Ideal for rails, kitchen and bar equipment and marine fittings near the coast.
Turns dull and chalky outdoors. We polish it bright and can seal it to slow the oxidation that brings the haze back.
Polishes well but rusts if left bare, so it usually gets plated or coated after polishing. We will explain the options before we start.
Soft castings with a thin skin. Pushing too hard opens pits, so we polish these by hand with light pressure and know when to stop.
Sending metal from Palm Desert comes down to five steps, and the first one only takes a phone camera and a few minutes.
Show us the piece, the damage and the look you want: mirror, bright or satin.
We check the metal and the condition, then send a written quote within 24 business hours.
Wrap, pad, insure and ship, with your quote number tucked inside. Prefer to deliver it yourself? Our Oceanside shop takes drop offs during business hours.
Old lacquer and tarnish come off, then scratches are worked out from coarse to fine wheels.
A final color buff, a full cleaning, an optional clear coat and a close look under bright light.
Sometimes Polishing Is All It Takes
Many customers call asking for plating when their piece only needs a good polish. If the part is solid brass, copper, stainless or aluminum and the damage is on the surface, polishing alone brings it back for less money and keeps the original metal you already like.
Plating is the answer when the color needs to change, when the metal underneath is steel that will rust, or when the old plating has already worn through to a different color. In those cases we still polish first, because a plated finish only looks as good as the surface under it.
Not sure which group your piece falls in? Look at a worn corner or the back side. If the color is the same all the way through, it is probably solid and a polish will do. If you see a different color peeking through, it is plated, and we will talk you through replating.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Every polished finish and restoration service we handle in house.
Polishing wheels have been turning in our shop since 1989. It is the skill every other finish we offer depends on, and the reason homeowners, designers and casino resorts keep sending us their metal.
Send a photo of your piece and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
One heirloom or a full hotel renovation, shipped to us from any state and returned insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
The pieces differ but the care is the same. These are the groups we polish for, and the hardware and fixtures each one tends to send.
Slot machine trim, table rails, bar fixtures and decorative accents polished to shine under bright lights day and night. Casino resorts across North County San Diego trust us with their gaming floors.
Bar rails, foot rests, door push plates and lobby fixtures brought back to a bright, welcoming finish.
Door levers, hinges, knobs and railings polished as a matched set so every room looks consistent.
Chandeliers, sconces, lamp bases and decorative pieces polished by hand, curves and details included.
Stainless cleats, rail fittings and bronze hardware cleaned of salt haze and polished to stand up to coastal air.
Family pieces, candlesticks and collectibles polished carefully so engraving, stamps and fine detail stay sharp.
Fast polishing leaves swirls, waves and rounded edges. We take the time each piece needs so the finish looks right from every angle.
Brass, stainless and aluminum each get their own wheels and compounds, so the surface is never burned, smeared or left hazy.
Every grit is fully removed by the next one before we move on. That is how a polish ends up clear instead of swirly.
Finished pieces are cleaned of all compound and inspected under strong light from several angles before they are approved.
A fresh mirror scratches easily, so each piece is wrapped in soft material and boxed to arrive just as it looked in our shop.
Keep that shine going strong
Handle a fresh mirror finish with clean, dry hands when you can. Skin oils leave fingerprints that show fast, and a quick wipe with a microfiber cloth takes them off before they set into the surface.
Desert sun and heat age lacquer faster, so check clear coats on sunny pieces every year or so. Keep bleach, glass cleaner and other harsh sprays away from the metal, since they can cloud lacquer and stain bare brass.
Unsealed pieces can be kept bright with a gentle metal polish and a clean microfiber cloth. Rub lightly in the direction of the grain on satin finishes, and use a fresh area of the cloth as it picks up black residue. Abrasive pads and kitchen scrubbers will scratch a mirror finish in seconds.
Near the ocean, salt air speeds everything up. Rinse outdoor hardware with fresh water now and then and dry it. When a piece finally loses its shine, send it back. A repolish is usually quick because the hard cutting work was already done the first time.
Metal Finishing Gallery
A look at recent work from our Oceanside shop: plated hardware, lighting, hospitality and casino pieces, marine fittings and industrial parts.
We take shipments from any state. These steps keep yours safe, and they help us find your job the day it lands.
Email photos of each piece, front and back, and the finish you want. You receive a written quote and lead time, usually the same business day. Wait for your quote number before you ship.
Wrap every piece on its own in soft cloth or bubble wrap so nothing rubs together in transit. Pad the box with at least three inches on every side and double box long rails or tubes.
Declare the full value with the carrier and email us the tracking number so we know what is coming and can log it the day it lands.
Once polishing is done we send photos for your approval, then pack your pieces in new materials and return them insured.
Every piece is polished, cleaned and inspected by hand in our own shop in North County San Diego.
Metal polishing, plating and finishing in San Diego County since 1989.
Palm Desert is across the mountains from Oceanside, roughly two hours by road, in the Coachella Valley. Most customers here ship pieces with tracking and insurance, and sun and heat make a repolish worth booking when the finish fades.
Looking at the region around Palm Desert? These cities are close by.
Frequently Asked Questions
Here are straight answers to questions we hear about polishing, shipping and quotes. If yours is missing, call or send us a message.
We are at 2613 Temple Heights Dr, Ste G in Oceanside. Business hours are Monday to Friday 8:00 AM to 5:00 PM and Saturday 9:00 AM to 2:00 PM. Receiving for shipped parts is Monday to Friday 8:00 AM to 4:00 PM Pacific.
Yes. Bar rails, signage trim, door hardware and decorative fixtures are all part of our work. We quote from photos and can polish a full set to one finish so every piece matches.
Yes. Slot trim, table rails, bar fixtures, lobby hardware and foot rails are part of our work. We quote large runs together and finish every piece to match.
Yes, carefully. Candlesticks, trays and family pieces are polished so engraving, stamps and fine detail stay sharp. We tell you what the metal can take and how bright we recommend going.
A clear coat helps brass and copper hold their color, and a soft cloth keeps dust from scratching the surface. Keep bare metal out of long direct sun when you can, and send it back for a repolish when the finish fades.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.