Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Good hardware makes a boat look cared for. For owners in Lemon Grove, we bring back bright chrome, satin chrome and polished nickel on cleats, chocks, wheels, rail ends and cabin pieces. Send it by carrier, or call us first and we will set a time to receive it.
A close look at how we restore boat hardware
Small and medium marine hardware is the best fit for our shop, and it happens to be easy to ship. That is good news for boat owners in Lemon Grove, because you can send us a box of cleats and fittings without hauling the whole boat anywhere.
We strip each piece, repair the pits, and replate it in copper, nickel and chrome. We have been doing plating work in Oceanside since 1989, so salt damage is nothing new to us.
Owners in La Mesa, Spring Valley and El Cajon ship to us the same way, and sets stay tagged together so matching pieces come back matching.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Not sure whether your hardware is on the list? Most small and medium marine pieces are. Here are the groups we see most from Lemon Grove and beyond.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
The process is the same for every customer, including the ones in Lemon Grove. Here is what to expect.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
Ship your hardware to our Oceanside shop in a padded box, or call ahead and bring it in yourself. Wait for your quote number before you send anything.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
We plate for weekend boaters, working captains and restorers. Customers in Lemon Grove fit right in with the groups below.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
Plated once, cared for always
People are sometimes surprised that restored hardware needs any care at all. It does, though much less than before. Owners in Lemon Grove who rinse and dry their fittings rarely see the old problems come back.
Add wax a few times a year and avoid abrasive cleaners, and your replated pieces should keep looking the way they did when they left our shop.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
From quote to return box, this is the short version of mailing us your hardware from Lemon Grove.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Hardware from Lemon Grove reaches us by carrier or by hand once you have called ahead. Between San Diego Bay and Mission Bay and warm sun and salt in the wind, boat metal in this area works hard, so ask for a quote early.
Nearby cities we help with marine hardware restoration.
Frequently Asked Questions
No jargon, just plain answers about replating boat hardware, including a few that apply to Lemon Grove.
Price depends mainly on condition, metal type, size and quantity, so there is no flat rate. A lightly tarnished cleat takes less work than a deeply pitted wheel. We quote from photos at no charge, and the price comes in writing.
We are at 2613 Temple Heights Dr, Ste G, Oceanside, CA 92056. Packages are received Monday to Friday, 8 AM to 4 PM Pacific. Customers close to the shop can phone first and bring the parts straight in. Call (760) 746 3378 before you send anything large, and always wait for your quote number.
Yes. Door latches, hinges, pulls, cabin lights, vents and small trim are common orders. These pieces set the tone below deck, and we restore them to match the finish on deck.
Yes. Send a photo of everything that needs work and tell us where each piece sits. We keep sets together, tag pairs and match the finish across the whole group so the boat looks even. A full set is quoted in writing from your photos.
That is the goal. We keep sets together, tag pairs and plate matching pieces the same way, so the finish looks even from bow to stern. If you are restoring only part of a set, tell us and we will explain what to expect.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.