Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Burrs, machining marks and rough corners come off in the tumbler, and the whole load gets treated alike. That's what Laguna Woods customers get when they send parts to Oceanside.
Bright, satin or aged, we've got the media
Boat and car people often have small metal parts that have seen better days: cleats, latches, trim pieces, badges and fasteners. Tumbling can clean up the surface before plating or polishing, and it's a gentle start for restoration. If that sounds like your project in Laguna Woods, we can help.
Tell us what the parts are, what metal you think they are and how rough they look. A few photos from Laguna Woods give us a good start. We often suggest a sample run, since older parts can surprise you.
If tumbling isn't the right first step, we'll recommend a different one. For parts from Laguna Hills or Aliso Viejo, the advice is the same: ask before you ship.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Here's what the tumbler can do for parts coming in from Laguna Woods, from light deburring to a full antique look.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
You don't have to live nearby to work with us.
Customers all over the country pack their parts and ship them to our Oceanside shop. We finish them, inspect them and send them back insured. It starts with a few photos.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Six steps get your Laguna Woods order from rough to ready. You'll hear from us at each stage that matters.
Tell us what the parts are, how many you have and the finish you are after.
Ship the Laguna Woods parts only after you have your quote number. Include your contact info on a sheet inside the box.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Hotels, casinos, shops and homeowners all send us hardware. Look over the list to see how Laguna Woods projects fit.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Before you pack, read this
Take a picture of the finish you hope to get, even if it's a different part or a sample from a catalog. Showing is faster than describing.
We'll compare it with what we can do on your metal and tell you how close the first run will land. Photos from Laguna Woods work as well as a visit would.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
The box matters as much as the parts inside. Here's how to ship from Laguna Woods the right way.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Laguna Woods is a small city tucked among the Orange County hills, near Laguna Hills and Aliso Viejo. If you're restoring a piece of furniture or refreshing hardware around the house, a few photos are enough to start.
If you're working out of a town near Laguna Woods, one of these pages may fit.
Frequently Asked Questions
Whether it's your first time or your fifth, these answers help. We wrote them with Laguna Woods in mind.
We tumble the parts to get the finish you want, then seal them with a clear lacquer. The coating helps the look last and slows dulling, especially on brass and copper.
Yes, though tumbling pays off from a few dozen pieces up. If you only have a handful, we'll tell you whether hand polishing suits the job better.
They're dry media for gentle polishing and drying. We use them when parts need a clean, light finish after wet tumbling, or when a harder media would be too aggressive.
Plastic media is usually the kindest to brass, aluminum and zinc. We also adjust cycle time, since even gentle media can overwork a soft part if it runs too long.
No. Steel media burnishes, which means it presses the surface smooth instead of cutting it. The result is a brighter, tighter surface on brass, copper and steel.
The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.
Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.
When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.