Skip to content

Boat Parts Plating Company Serving Hemet

Every pit filled, every spoke polished and plated

Peeling chrome and rust bleeding from the base are signs the plating has failed. We remove all of it and rebuild boat hardware for people in Hemet with copper, nickel and chrome. Our shop is one business day away by ground from Hemet, so shipping is easy.

Certified, Approved and Verified

Hemet Boat Parts Chrome Shop

Plating you can plan around, quote first

If you own a boat in Hemet, there is a good chance a cleat, chock or rail fitting on it has started to pit or peel. That is what salt, sun and years of use do to chrome. We have been replating boat and yacht hardware in Oceanside since 1989, and bringing worn pieces back is a big part of what we do.

Our method is not a quick touch up. Old plating is stripped off, pits are filled with copper and leveled by hand, and then nickel and chrome go on in layers. Boaters in San Jacinto, Perris and Menifee can follow the same simple path: take a few photos, tell us what each piece is, and wait for our quote.

We tell you plainly what we find. If a fitting is too far gone to save, we say so before you spend anything, and if it is worth saving you get a written quote and a lead time you can plan around.

We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.

What We Restore

Marine Hardware We Bring Back

Every piece on this list gets stripped, repaired and replated, whatever the metal. Photos from Hemet are all we need to get started on a quote.

Restored chrome boat cleat and chock in daylight

Cleats and Chocks

Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.

Rechromed boat steering wheel hub and spokes

Steering Wheels and Hubs

Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.

Chrome rail fittings and stanchion bases restored

Rail and Stanchion Fittings

Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.

Restored bronze hawse pipe and fairlead in chrome

Hawse Pipes and Fairleads

Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.

Replated turnbuckles, pad eyes and deck rings

Rigging and Line Hardware

Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.

Restored cabin door latches, hinges and handles

Cabin Hardware and Trim

Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.

Restoration Results

Before and After

Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.

Bronze deck cleat after chrome restoration
Pitted deck cleat with peeling chrome before restoration Before
After

Bronze Deck Cleat

Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.

BRIGHT CHROME BRONZE SALT DAMAGE
Boat steering wheel hub and spokes after rechroming
Boat steering wheel with rusted, dull chrome before restoration Before
After

Helm Wheel and Hub

Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.

SHOW CHROME STEEL HELM
Hawse pipe after restoration in bright chrome
Worn hawse pipe with rope grooves and corrosion before restoration Before
After

Classic Hawse Pipe

Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.

BRIGHT CHROME BRONZE ORIGINAL PART
One Piece or a Thousand

Big order or a single knob, same care.

Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.

Tap to add photos (up to 5). JPG, PNG, WEBP or iPhone HEIC.
    Know What You Are Looking At

    Three Signs Your Hardware Needs Replating

    Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.

    Most common

    Pitted or Peeling Chrome

    • Tiny dark dots across the surface
    • Chrome lifting in flakes at the edges
    • Rust stains bleeding from the base
    • We strip it all and fill every pit
    • Rebuilt with copper, nickel and chrome
    Bronze and brass

    Green or Black Corrosion

    • Green crust around bolts and edges
    • Plating worn through to bare metal
    • Dark spots that polishing cannot reach
    • Cleaned down to solid, healthy metal
    • Replated to stop the color from returning
    Older hardware

    Worn, Rough or Soft Metal

    • Grooves cut by years of rope or chain
    • Bubbling on old pot metal castings
    • Edges rounded by heavy use
    • Grooves smoothed and leveled by hand
    • We tell you honestly if a part is too far gone
    What Your Hardware Is Made Of

    Marine Metals We Work With

    Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.

    Classic marine

    Bronze

    The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.

    All finishes

    Brass

    Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.

    All finishes

    Stainless Steel

    Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.

    Our specialty

    Pot Metal and Zinc Die Cast

    Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.

    All finishes

    Steel

    Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.

    Ask us first

    Aluminum and Other Alloys

    Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.

    How It Works

    From the Dock to Our Bench and Back

    A quote, a box, a bit of waiting and a bright finish. That is the short version of how it works for Hemet owners.

    1

    Remove and Photograph

    Take the hardware off the boat, snap a few photos and note where each piece goes.

    2

    Get Your Quote

    We look at the metal and the damage, then send a written price and lead time within 24 business hours.

    3

    Ship or Drop Off

    Pack each fitting on its own, insure the box and send it from Hemet. We start work as soon as it arrives in Oceanside, once you have your quote number.

    4

    Strip, Repair and Plate

    Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.

    5

    Inspect and Return

    Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.

    Marine Restoration Catalog

    Fittings, Finishes and Services

    A quick list of the boat and yacht hardware we restore and the finishes we offer.

    Deck and Docking

    • Horn Cleats
    • Flip Up and Pop Up Cleats
    • Bow and Stern Chocks
    • Hawse Pipes
    • Fairleads and Chafe Plates
    • Bow Eyes and Deck Rings
    • Pad Eyes
    • Turnbuckle Bodies

    Helm, Cabin and Trim

    • Steering Wheels and Spokes
    • Wheel Hubs and Center Caps
    • Rail Ends, Tees and Elbows
    • Stanchion Bases
    • Cabin Door Latches and Hinges
    • Cabin Lights and Vents
    • Horns and Bells
    • Small Trim Pieces

    Finishes and Services

    • Bright Chrome
    • Satin Chrome
    • Polished Nickel
    • Copper Leveling for Pits
    • Full Strip and Replate
    • Pot Metal Repair
    • Set Matching
    • Photo Approval Before Return
    What Our Clients Say

    Trusted by Professionals

    From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.

    Boat cleats and fittings laid out on a workbench before plating
    Plating line at Decorative Metal Coatings
    35+ Years of Expertise
    Take a Moment to Learn More

    About Decorative Metal Coatings

    We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.

    Free Estimates Available

    Send a photo of your hardware and receive a no obligation quote within 24 hours.

    Quality Guaranteed

    Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.

    Ship From Anywhere in the US

    Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.

    Fast Turnaround Times

    Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.

    Who We Serve

    From the Marina to the Casino Floor

    We work with private owners, charter operators, marinas and restoration shops. If you are in Hemet and fit one of these groups, read on.

    Polished chrome rail fittings and stanchion bases on a waterfront resort bar

    Casinos and Resorts

    The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.

    Restored chrome cleat on the varnished deck of a classic wooden boat

    Classic and Wooden Boats

    Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.

    Bright chrome rail fittings on a yacht deck in sunlight

    Yachts and Cruisers

    Rail fittings, cleats and helm hardware refinished so every piece on deck matches.

    Restored chrome hardware on a sportfishing boat at the dock

    Sportfishing and Charter Boats

    Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.

    Restored chrome dock cleat at a marina

    Marinas and Yacht Clubs

    Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.

    Boat fittings sorted on a shipwright's bench for replating

    Restorers and Shipwrights

    Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.

    Our Commitment

    Hardware Restored to Last

    Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.

    Full Strip First

    Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.

    Layered Protection

    Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.

    Daylight Inspection

    Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.

    Sets Kept Together

    Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.

    What We Do Differently

    • We strip every part instead of plating over old chrome
    • Pits and rope grooves are filled and leveled by hand
    • Nickel goes under the chrome for real corrosion protection
    • We tell you plainly if a fitting is not worth saving
    • Photos are sent for approval before parts ship home

    What You May Experience Elsewhere

    • Chrome sprayed or plated right over corrosion
    • Thin plating that pits again after one season
    • Rope grooves and pits left showing under the finish
    • Mismatched color across a set of fittings
    • Parts returned loose with no protection in the box

    Keeping Restored Chrome Bright in Hemet

    Simple habits that protect your chrome

    Valley heat bakes grime onto chrome, and a boat that is trailered home from the lake and put away wet can show water spots that are hard to remove later. Look your hardware over now and then, because catching a small spot early is cheaper than redoing a whole set.

    If your boat sits for weeks at a time, cover the hardware or wipe it down before storage. Moisture trapped under a cover can do as much harm as rain. A light coat of wax before a long break is cheap insurance.

    Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.

    If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.

    Before You Ship

    Small Hardware Travels Well, Big Pieces Need a Plan

    Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.

    Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.

    If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.

    Nationwide Service

    Mail Us Your Hardware From Any Port in the US

    Four steps take you from a quote to a bright box at your door in Hemet.

    01

    Ask for a quote

    Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.

    02

    Wrap every piece

    Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.

    03

    Tag the sets

    Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.

    04

    Approve and receive

    When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.

    Visit Us

    Our Location

    Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.

    Decorative Metal Coatings

    Chrome and nickel restoration for boat and yacht hardware since 1989.

    Business Hours

    • Monday to Friday 8:00 AM to 5:00 PM
    • Saturday 9:00 AM to 2:00 PM
    • Sunday Closed

    Our door is open to Hemet

    Because Hemet is in Southern California, shipping time is short. Pack your hardware well, send it to our Oceanside address, and we will take over from there.

    Nearby Cities We Serve

    Explore our boat hardware restoration pages for these nearby cities:

    Boat Hardware FAQ Near Hemet

    Frequently Asked Questions

    Here are the questions boat owners ask us most, with answers written for people in Hemet.

    Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied with the work, we make it right. Ask us about the details when you request your quote, and we will explain them in writing.

    Email photos of each piece with a note about the metal, where it sits on the boat and the finish you want. We reply with a free written quote, usually within 24 business hours, with a price and a lead time for each piece.

    Yes. Every piece is checked in daylight, where any flaw shows. We send photos for your approval, then repack everything in fresh materials and ship it back insured. Nothing leaves the shop until it has passed that check.

    Yes. Small and medium hardware ships well in a regular box. From Hemet, ground shipping to our Oceanside shop usually takes one business day, and your parts come back insured with tracking.

    Chrome looks the same once it is on, but each metal needs different prep. Bronze takes copper easily, and stainless needs a nickel strike first. We plan the work for each metal so a mixed set still matches.

    The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.

    Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.

    When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.