Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Burrs, machining marks and rough corners come off in the tumbler, and the whole load gets treated alike. That is what you get when Encinitas parts come to our Oceanside shop.
We Look at Your Parts Before We Run Them
Nobody wants to find out after the fact that a finish came out wrong. That is why every job at our shop starts with a sample run. A few of your pieces go into the tumbler first, and we show you what the finish looks like before the rest of the box is touched.
The sample tells us a lot. We learn which media works, how long the cycle needs to be and whether the edges stay as sharp as you want them. For parts coming from Encinitas, that sample can be the difference between a good batch and a surprise.
After you approve it, the full batch runs with the same settings, in stages when needed. Shops in Carlsbad and Solana Beach and makers around Cardiff can follow the same route. The quote comes first, the sample second and the full batch third.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Every tumbling job starts with a goal, maybe safer edges, a brighter surface or a softer look. These are the services we offer to get there.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
See the price before you ship a thing.
Snap a few photos from different angles and tell us the finish you have in mind. You'll get a written quote and a realistic lead time. Standard work takes 3 to 5 weeks, and expedited orders are possible when the schedule allows.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Quote, sample, full batch, check, pack. These are the steps we follow on every job, no matter where in California the parts come from.
Tell us what the parts are, how many you have and the finish you are after.
Bring the parts to our Oceanside shop or send them in a strong box with insurance. After your quote number arrives, call ahead if you plan to stop by.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
From casino trim to cabinet pulls, small metal parts show up in a lot of places. Here are the kinds of work we finish in the tumbler most often.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Small Details That Save Everyone Time
Photos matter. Show us a whole part, a close up of the edges and, if possible, an example of the look you want. With those and a part count we can usually say what media and finish make sense.
Soft metals like aluminum and zinc die cast need lighter media and shorter cycles. If your parts are made from either, say so and we plan the run to protect the fine detail.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
Here is the short version of shipping to us. Get a quote, wait for the quote number, pack the box well and let us know it is coming.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Encinitas is a coastal town known for surf culture and the shops along Highway 101. Salt air is tough on beach cruisers, railings and outdoor fixtures. Parts can be tumbled and then plated, patinaed or lacquered for protection, and you can drop them off or ship them.
Here are three cities around Encinitas where we offer the same service.
Frequently Asked Questions
Got a question that is not listed? Call or send a photo and we will answer it directly.
Only slightly. It removes a tiny amount of metal and rounds corners. If your parts have tight tolerances or edges that must stay sharp, tell us before we quote so we can pick gentler media or shorter cycles.
Yes. We work on bicycles, boat and yacht parts and other restoration pieces. Salt air is hard on bare metal, so ask about plating or clear lacquer after tumbling. Drop off in Oceanside or ship a box.
Yes. Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables. Hinges, pulls and knobs are common jobs, and a matching set looks even throughout.
Burnishing uses stainless steel pins or balls that press the surface smooth instead of cutting it. It brings up a bright, clean shine on brass, copper and steel without buffing each piece.
Small parts are run in a vibrating bowl or barrel with media and compound. The media rubs against the metal, removing burrs and smoothing the surface. Depending on the media and the time, the result can be matte, satin or bright.
Not at all. Most of what comes through our door is home and business hardware: faucets, light fixtures, door handles, cabinet pulls, railings and decorative pieces. We also work for hotels, restaurants, boat owners and manufacturers.
Tell us what the part is, roughly how big it is, how many pieces you have and the finish you're after. If you know the metal, mention it. If not, that's fine. We can usually tell from the photos.
Every part is quoted on its own. The biggest factors are condition, the base metal, size and shape, the finish you choose and how many pieces you send. A part with deep pits or broken spots takes more work before it can be plated.