Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
A good finish starts with the right media. We match it to your metal and your parts, then confirm the look on a sample before running the full batch for Cypress.
Batch After Batch, the Same Finish
Sending parts to a shop you have never visited takes some trust, so here is exactly how it works. You send photos, the metal and a part count. We write back with a price and a lead time, and you wait for the quote number before shipping anything.
Then you bag the parts by part number, pack them tight in a strong box, insure the box for its real value and email us the tracking number. Put a printed sheet inside with your contact details, the quote number and what you want done.
That is the whole routine for Cypress, and it is the same for Buena Park, La Palma and Los Alamitos. When your parts are finished, we pack them by part number and ship them back insured.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
Deburring, smoothing, burnishing and decorative finishes all start in the same machine. The media and the cycle time decide which one you get.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
You don't have to live nearby to work with us.
Customers all over the country pack their parts and ship them to our Oceanside shop. We finish them, inspect them and send them back insured. It starts with a few photos.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Here is how a tumble finishing job moves through our shop, from your first photos to the box that comes back to Cypress.
Tell us what the parts are, how many you have and the finish you are after.
Parts travel best bagged by part number and packed tight. Ship them insured to Oceanside after your quote number arrives, and send the tracking number to us by email.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
Makers, manufacturers, designers and restorers all use tumbling for different reasons. These six groups cover most of the parts that come through our shop.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
Good Info In, Good Finish Out
Before you box anything up, take a few minutes to describe the job. How many pieces, what metal, where the parts end up and what the surface should feel like. That short note shapes the whole run.
Pieces that touch each other can mark each other, so we run delicate parts with extra care. Tell us if yours are thin walled or finely detailed, and we adjust the media and the cycle.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
A little care with the packing goes a long way. Here is how to send parts from Cypress so they arrive in good shape and return the same.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Cypress is a suburban Orange County city that borders Buena Park, La Palma and Los Alamitos, with office parks and light industrial space along its main roads. Small shops here can send metal parts in one box and get a written quote first.
Other places near Cypress we serve, with the same steps and the same free quotes.
Frequently Asked Questions
Here are the questions we hear most about tumble finishing, shipping parts from Cypress and getting a quote.
Tumbling finishes many parts at once, reaches recesses and costs less per part. Hand polishing gives a true mirror shine on flat faces and keeps edges crisp, which suits large or delicate pieces.
A few dozen pieces is a good starting point. Tumbling really pays off with a full box or a production run, and we can quote either. For fewer pieces, hand polishing may be the better choice.
Not if they are handled right. We rinse and dry steel quickly so the bare metal does not flash rust, and we check every batch before it is packed or sent on to plating.
Burnishing uses stainless steel pins or balls that press the surface smooth instead of cutting it. It brings up a bright, clean shine on brass, copper and steel without buffing each piece.
Yes. After you ship, email us the tracking number so we know your box is on the way and can watch for it at our receiving desk.
The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.
Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.
When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.