Deburring
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Parts tumbled with care, checked for stuck media and dried spot free. Start with a few photos from Coachella and we will take it from there.
From rough castings to soft satin brass
The pieces that tumble along with your parts decide the finish. In the shop we use ceramic, plastic, porcelain, stainless steel pins and balls, and dry walnut shell or corn cob. A customer in Coachella does not need to pick one, because we match the media to the part.
Ceramic cuts fast on hard metals, plastic is gentle on soft ones, porcelain leaves a bright surface and stainless steel burnishes. Compounds and water clean the parts, protect them from tarnish while they run and help control how bright the finish turns out.
All you need to send from Coachella is photos, the metal and the count. Parts from Indio and La Quinta get the same attention to detail. Drive them to Oceanside if that suits you, or pack a box and ship it. Either way we quote first.
Not sure which finish your parts need? Send photos, a part count and what the parts are used for. We will suggest a finish, run a few samples if needed, and send back a written quote.
These services work on brass, bronze, copper, steel, stainless, aluminum and zinc, and every run is matched to the metal.
Burrs and sharp slivers left by machining, stamping or casting are worn away evenly, so parts are safe to handle and ready for assembly or plating.
Sharp corners are gently rounded and tool marks are softened. Parts feel better in the hand and plating covers edges more evenly.
Steel media presses the surface smooth instead of cutting it, bringing up a bright, clean shine on brass, copper and steel without buffing each piece.
A soft satin surface with worn, rounded edges that looks naturally aged. Popular on brass hinges, pulls, knobs and small decorative castings.
Tumbling first removes scale, light rust and surface marks, so copper, nickel or chrome goes on smoother and the finish looks better for less cost.
Plated or darkened parts are tumbled lightly so the high points wear through and glow, giving hardware a used, lived in character.
Drag the handle across each photo to see parts as they went into the tumbler and as they came out.
Before
Rough castings with parting lines and a dull, uneven skin. Tumbled in stages to smooth the surface and soften the edges into an even satin glow.
Before
Fresh off the machine with burrs, sharp corners and cutting oil. Deburred, edge smoothed and dried spot free, ready to go straight to plating.
Before
Bright, brand new brass that looked out of place in an old home. Darkened and tumbled so the edges wear back to brass, like decades of use.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Each method has its place. The right one depends on how many parts you have, their shape and the look you want.
The small pieces that tumble with your parts decide how much metal is removed and how the surface looks. We choose them part by part.
Heavy and abrasive. Used to take down burrs, casting skin and tool marks on steel, stainless and other hard metals.
Lighter and gentler, so it smooths brass, aluminum and zinc without cutting too deep or rounding details away.
Fine and dense. It cuts very little and leaves a smooth, bright surface ready for plating or a final polish.
Pins, balls and small shapes that press the surface smooth rather than wearing it away, bringing up a bright shine.
Dry natural media used with polishing compound for a soft luster, and to dry parts without water spots.
The liquid in the tumbler cleans, protects parts from tarnish while they run and helps control how bright the finish turns out.
Follow your parts from quote to return. Each step is meant to protect the metal and your schedule.
Tell us what the parts are, how many you have and the finish you are after.
Choose shipping or drop off. Bag parts by part number, add your quote number and contact info, and we take it from there.
We tumble a few pieces first so you can see and approve the finish before the full batch.
Parts run with the media and cycle time dialed in from the sample, in stages when needed.
Every batch is rinsed, dried spot free and checked for lodged media and missed burrs.
Parts move on to plating or patina, or are packed by part number and shipped back insured.
Hard metals and soft metals behave very differently in a tumbler. Each gets its own media and cycle time.
Take a beautiful satin or burnished finish and are the go to metals for the decorative tumbled look on hardware and castings.
Deburred and smoothed with cutting media, then rinsed and dried quickly so the bare steel does not flash rust before plating.
Tough enough for aggressive media. Tumbling gives stainless an even satin or bright burnished look without hand polishing.
Soft and easy to over process, so it runs with lighter media and shorter cycles to protect details and dimensions.
Soft castings with fine detail. Gentle media removes parting lines and flash without rounding off the design.
Light tumbling over plating creates a worn antique look. We review these first, since too much time cuts through the finish.
Since 1989 we have finished metal for manufacturers, designers and restorers. Tumbling, plating and patina all happen under one roof, so your parts go from rough to finished without changing hands.
Send photos and a part count and receive a no obligation quote within 24 hours.
Every batch leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Small parts in bulk ship easily and affordably. Send a box from any state and get it back insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Everything we do in the tumbler, the finishes it creates and the services that often follow.
Tumbling looks easy from the outside. Getting the same result on hundreds of parts without damaging a single one takes care.
A few parts are run and approved before the full batch, so there are no surprises when the rest come out.
Media size and type are matched to the metal and the holes in each part, to avoid lodging and over cutting.
Finished parts are checked for leftover burrs, stuck media and water spots before they are packed.
Different parts are run and packed separately and labeled the way you sent them, ready for your stock shelf.
If your work is on this list, tumbling can probably save you time. If it is not, send a photo and ask.
Small brass trim, table hardware, rail fittings and decorative accents finished in matching batches, so replacement pieces blend in with the rest. Trusted by casino resorts across North County San Diego.
Hinges, pulls, knobs and escutcheons with a soft tumbled finish that matches across an entire home or project.
Production parts deburred and smoothed in volume, ready for plating, coating or assembly.
Furniture makers use tumbled hardware for a warm, hand finished look on cabinets, chests and tables.
Small lamp parts, finials, canopies and fittings given an even finish before plating or patina.
Buckles, keychains, tags and other small metal goods finished in batches for makers and growing brands.
A short checklist for better results
A good order starts with a good description. We need the metal type, the part count and a clear idea of the finish, whether that is satin, bright, matte or aged.
If your parts have sharp details or tight fits, say so. We would rather hear about it at quote time than find out after the batch runs.
Point out holes, slots and threads. Media can wedge into openings that are close to its size, so we pick a media shape and size that stays clear of them. Telling us the hole sizes up front saves time for everyone.
Finally, let us know what happens next. Parts that will be plated get a different finish than parts that will be lacquered or left bare, and parts headed for an assembly line can be packed the way your team needs them.
Tumble Finishing Gallery
Hardware, castings and production parts deburred, smoothed and tumbled in our Oceanside shop.
No pallet needed for most jobs. Pack your parts from Coachella in a sturdy box and follow the steps below.
Send photos, the metal type and a part count. You will get a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Keep each part type in its own labeled bag. Mixed parts take longer to sort and hard pieces can mark softer ones on the way here.
Small parts are heavy, so use a strong box and fill the empty space. Insure the box for its real value and email us the tracking number.
We send photos of the sample or finished batch when needed, then pack everything by part number and ship it back insured.
Local shops and makers are welcome to drop off parts for tumbling at our facility in North County San Diego.
Tumble finishing, plating and patina under one roof since 1989.
Coachella lies in the eastern Coachella Valley, a desert farming area known for date palms and for the music festival that borrowed its name. Standard turnaround is 3 to 5 weeks, and expedited orders can take 5 to 7 business days as availability allows.
Nearby towns like Indio, La Quinta and Thermal follow the same process. These city pages cover the area.
Frequently Asked Questions
Read these before you ship a box from Coachella. They can save you a phone call, though you are always welcome to call.
Some parts need more than one pass. We might cut first with harder media, then smooth with a gentler one, then dry and finish. Each stage is checked before the next.
We check them against your quote and part numbers, then run a sample so you can approve the finish. After that the full batch runs, gets rinsed, dried and checked, and goes back to you packed by part number.
Show the whole part, any rough areas and an example of the finish you want, if you have one. Add the metal type and how many parts you have.
In most cases, yes. Coachella lies in the eastern Coachella Valley, a desert farming area known for date palms and for the music festival that borrowed its name. Tumbling can deburr, smooth and brighten parts like these, and a sample run shows you the result before the full batch.
Yes. Clear lacquer is one of the services that pairs with tumbling, and it helps protect brass and other metals that tarnish.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.