Show Chrome Restoration
Triple plated in copper, nickel and chrome and buffed by hand between layers, for the deep, wet shine that makes small trim stand out on a finished build.
We strip old plating down to bare metal, fill the pits and rebuild the finish in copper, nickel and chrome. Start your quote from Clairemont with a few clear photos.
A shop built around small classic parts
Pot metal is the reason a lot of classic parts get turned away, and it is the reason people in Clairemont end up calling a specialist. Door handles, hood ornaments and dash knobs from the old days were often cast in it, and when the chrome bubbles, the metal underneath is usually pitted.
Pitted pot metal does not scare us. We strip the part, fill the pits with copper, level it by hand and only then plate it. If you are in Pacific Beach, Linda Vista or Mira Mesa, you can drop the parts off in Oceanside or ship them, whichever is easier.
Some parts are too far gone, and we tell you that before we start. Most are not, and a part that looked like scrap on the bench often comes back looking new.
Small parts are our sweet spot, and they are easy and affordable to ship from anywhere in the country. Send a few photos, tell us what the parts came from and how you want them to look, and we will send back a written quote.
Six services, one shop, and a quote based on your photos before any work starts.
Triple plated in copper, nickel and chrome and buffed by hand between layers, for the deep, wet shine that makes small trim stand out on a finished build.
Pitted and blistered pot metal is stripped, filled and leveled in copper before it is plated. Slow, careful work that saves parts most shops send back.
Bright or satin nickel for earlier cars and motorcycles that left the factory with a softer, warmer shine than modern chrome.
Knobs, handles, window cranks, bezels and switch plates restored so the inside of your classic matches the outside.
Levers, clamps, mirror stems, small covers and controls replated so a vintage bike looks right from every angle.
Original bolts, nuts, clips and small brackets cleaned and replated, so you keep correct factory hardware instead of buying generic replacements.
Drag the handle on any photo to see the part as it arrived and as it left our shop.
Before
Bubbled, flaking chrome over pitted pot metal. Stripped, filled in copper, leveled by hand and triple plated in show chrome.
Before
A thin steel ring with surface rust and worn plating. Stripped, polished and finished in bright nickel and chrome.
Before
A coffee can full of rusty original bolts, clips and small brackets. Cleaned, sorted and replated as a matching set, ready to go back on.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
Owners, shops and collectors trust us with parts that are hard or impossible to replace.
Not every part needs the same treatment. Picking the right level for each piece keeps your budget where it matters most.
Classic parts were made from a handful of metals, and each one needs its own preparation before it can shine again.
Used for door handles, hood ornaments, interior knobs and many trim pieces. We stop the pitting, fill it in copper and level it by hand before plating.
Brackets, bezels, levers and hardware. Rust is removed down to clean metal, then the part is polished and plated in copper, nickel and chrome.
Common on early vehicles, lamps and fittings. Brass takes nickel and chrome beautifully once it has been cleaned and polished.
Some trim pieces and motorcycle covers are aluminum. They need a special pretreatment before plating, so we review each piece before quoting.
Many classic trim pieces are stainless and may only need polishing. If yours does need plating, it gets a nickel strike first so the finish bonds.
Older fittings and hardware in copper or bronze clean up well and plate easily, whether you want them chromed or nickeled.
It is a simple process, and we keep you updated whenever a part needs a decision from you.
Photograph each part from a few angles and tell us what it came from and the finish you want.
We check the condition and the metal, then send a written quote and lead time within 24 business hours.
Bring them in person or ship them. Wrap each part by itself so metal never touches metal.
Old plating and rust come off, pits are filled, and the surface is leveled and polished by hand.
Copper, nickel and chrome go on in layers, then every part is inspected, packed and returned insured.
What Size Parts Make Sense to Ship
Most of the classic and vintage work that comes through our door fits in a small box. Handles, knobs, bezels, levers, brackets, hardware and short trim pieces are light, they pack easily and the shipping cost both ways stays reasonable. For owners outside California, these are the parts where mailing them to a specialty shop makes the most sense.
Larger pieces like bumpers, grilles and full length trim are a different story. We can plate them, but they need oversized boxes or freight, and the trip here and back can add up quickly. If you live in Southern California, the easiest option is simply to bring them to the shop.
If you are farther away and still want us to handle a large part, we are happy to take a look. Send photos and measurements, we will quote the plating, and you can weigh that against the shipping before you decide. No pressure either way.
A quick list of the classic and vintage parts and finishes we handle most often.
We have been restoring plated parts since 1989. Car owners, motorcycle restorers and private collectors send us the pieces they cannot replace, because we take the time to save them.
Send photos of your parts and get a no obligation quote within 24 hours.
Every restored part is backed by our craftsmanship guarantee. If something is not right, we make it right.
Small parts travel easily from any state and come back to you insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
On a classic, people look closely. Every shortcut in stripping or prep shows up later as peeling, pits or haze, so we do the slow work first.
Old chrome and nickel are fully removed, so the new layers bond to clean metal instead of a finish that is already failing.
Copper is built up and leveled by hand until pits disappear, which is what separates a show finish from a quick rechrome.
Every part is checked for haze, pits and missed spots before it is approved to leave the shop.
Each restored part is wrapped on its own, so fresh chrome never rubs against another piece on the way home.
Anyone with a classic that deserves a proper finish is who we are here for.
Antique slot machine trim, handles and casino collectibles restored to their original shine. Casino resorts across North County San Diego trust us with their decorative metal work.
Private owners and restoration shops rebuilding American and European classics, one small part at a time.
Riders and builders bringing old bikes back to original condition, or giving a custom build a clean, bright finish.
Shops that need dependable show chrome on small parts, with clear quotes and consistent quality job after job.
Owners getting ready for shows and judging who need finishes that hold up under a very close look.
Collectors of automobilia and vintage hardware who want a treasured piece to look the way it did when it was new.
Look after the finish and it will look after you
Coastal air in Clairemont carries moisture almost every day. On a classic that sits outside or in an open garage, that moisture can turn small chips into rust spots over time, which is why a good wax or sealer is worth the few minutes.
Park under a breathable cover rather than plastic, and wipe parts down after damp mornings. Nickel parts, which are softer than chrome, deserve the most gentle handling.
Skip steel wool, rubbing compound and harsh wheel cleaners. They scratch the surface and can cut through the chrome to the nickel underneath. If a spot needs more than soap, use a polish made for chrome and a soft cloth. Nickel is softer than chrome, so treat nickel parts gently and always dry them well.
For storage, keep parts and vehicles somewhere dry under a breathable cover, never plastic that traps moisture. If you notice small rust spots or lifting plating, send us a photo. Catching a problem early is always easier than waiting.
Restored Parts Gallery
Door handles, bezels, cranks, levers and original hardware from classic cars and vintage motorcycles, restored in our Oceanside shop.
Plenty of classic parts are small enough to mail for a modest cost. Follow these steps from Clairemont and they arrive in good shape.
Send photos of every part and the finish you want. You will get a written quote and lead time, usually the same business day. Please wait for your quote number before you ship.
Wrap each part on its own so metal never touches metal, and use a box just large enough for the parts and padding. A snug box keeps parts safe and keeps the shipping cost down.
Bag and label small hardware by where it goes so sets come back together easily. Declare the real value with the carrier and email us the tracking number.
When your parts are finished we send photos for your approval, then pack them in fresh materials and ship them back insured.
Local car and motorcycle owners are welcome to drop off parts at our shop in North County San Diego. It is also the easiest option for larger pieces.
Chrome, nickel and copper restoration for classic and vintage parts since 1989.
Small parts mail well and large ones do not, so from Clairemont we suggest you bring bumpers, grilles and long trim to the shop and ship the small items.
Looking for a page closer to home? These nearby cities have their own pages.
Frequently Asked Questions
Here are the questions we get most about restoring classic car and motorcycle parts, with straight answers for owners in Clairemont.
Handles, knobs, bezels, levers, brackets, hardware and short trim ship well. They are light, and the cost both ways stays reasonable.
It comes off completely. We strip to bare metal so the new layers bond to clean metal rather than to a finish that is already failing.
Yes. Levers, clamps, mirror stems, headlight rims and small engine covers are regular work, and riders can ship from Clairemont the same way car owners do.
Dry them right after washing, wax them every few months and store them under a breathable cover. Avoid plastic, which traps moisture against the metal.
We can plate them, but large pieces need oversized boxes or freight, which adds cost. If you live in Southern California, bringing them to the shop is the easiest option.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.