Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Bronze that turned green, steel that rusted at the base, chrome that lifts in flakes. We work on all of it, and we fix it for boat owners in Chino with a proper strip and a layered replate. Not near Oceanside? That is fine. Photos from Chino get you a quote, and parts usually arrive in one day.
Rebuilt From the Metal Up, Not Just Polished
Everything starts with photos. Take a few of each piece, tell us where it sits on the boat, and we send back a written quote and lead time within 24 business hours. That works the same from Chino as it does across town.
A written quote means no surprises. It lists what we plan to do, the finish you picked and how long it usually takes, which is 3 to 5 weeks for standard work.
If a deadline matters, ask about expedited work. Depending on availability it can be done in 5 to 7 business days, which helps when a boat has to be ready for a trip. The steps are the same in Chino Hills, Ontario or Chino.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Hardware from the helm, the deck and the cabin finds its way to our bench. Here is what we restore, and what you can expect for a piece shipped from Chino.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
Not sure what your part needs? Send us a photo.
We'll tell you what the metal is, what it takes to bring it back and what it costs. A written quote usually comes back within 24 business hours, and there's no obligation.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
From a quick photo to a finished fitting, this is how restoring boat hardware works when you are in Chino.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
Once you have your quote number, wrap the parts, put a printed sheet in the box and ship by ground. From Chino it usually takes one day to reach us.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Hardware does not care whether it sits on a yacht or a resort bar rail. We restore both, and these are the groups we work with, including owners in Chino.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
A Few Minutes of Care Goes a Long Way
Cleaning does not need to be complicated. Mild soap, fresh water and a soft towel handle most of what boating around Chino throws at hardware, including inland heat and sun. Save the heavy products for the hull and keep them off the chrome.
Handle restored hardware with clean hands and soft cloths when you install it. Fingerprints and grit scratch bright chrome. Keep the protective wrapping on each piece until you are ready to bolt it on, then remove it slowly.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
Before you ship anything from Chino, read these four steps. They keep your hardware protected and your quote on track.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Chino is home to the Planes of Fame Air Museum and a lot of Inland Empire industry. Boats from here are usually towed to Lake Elsinore or the Colorado River, and sun and long tows add up on chrome.
We also restore boat and yacht parts for owners in these nearby cities.
Frequently Asked Questions
Answers to questions boat owners in Chino ask about restoring hardware and shipping it to our Oceanside shop. If yours is missing, call us or send photos.
Yes. You can send photos any time, whether the boat is on the trailer, in a yard or in a garage. Hardware that has sat for years often just needs a full strip and a fresh set of layers.
We look at the metal and the damage, then send a written quote with a price and lead time within 24 business hours. Wait for your quote number before you ship anything, and put that number on a printed sheet in the box.
Bright chrome is the mirror shine most people picture on a cleat or rail. Satin chrome has a softer, lower glare finish. Polished nickel is a third choice with a slightly warmer tone. We can help you choose from photos.
One piece is fine. Keep in mind that a single bright piece beside tired ones can look odd, so sending the full set often gives a better look. We can quote both ways.
Aluminum needs special pretreatment, so we review it part by part. Send a photo or tell us the alloy name and we will confirm what is possible before you ship anything.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.