Cleats and Chocks
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
We restore marine hardware for Calimesa boat owners, from small deck cleats to helm hubs and cabin latches. Each piece is stripped, filled where it is pitted and plated with copper, nickel and chrome. Start with photos from Calimesa. After you approve the quote, a box to Oceanside usually takes one day by ground.
A Proper Restoration Starts With Bare Metal
Few things on a boat get touched as often as the helm wheel. Spokes lose their shine, hubs pit and center caps go dull. We restore metal wheels and hubs for boat owners in Calimesa in bright chrome or polished nickel.
Wheels with wood or rubber rims get a closer look first. We want to plan around those materials so the rim is not damaged while the metal is stripped and plated again.
Photos tell us most of it. Send a few shots of the wheel from Calimesa, Yucaipa or Beaumont, note the rim material and we will tell you how we would handle it.
We focus on smaller hardware because it ships easily and affordably from anywhere in the country. Send a few photos, tell us what each piece is and where it sits on the boat, and we will send back a written quote.
Not sure whether your part is on the list? These six groups cover most of what boats carry, and if yours is something else, send a photo from Calimesa and we will tell you.
Horn cleats, flip up cleats and bow chocks take rope wear and salt every day. We strip them, fill the pits and rebuild a hard, bright chrome that looks like the day it was cast.
Metal wheels, spokes, hubs and center caps restored in show bright chrome or polished nickel. Wheels with wood or rubber rims are reviewed first so we can plan around them.
Rail ends, tees, elbows, stanchion bases and mounting flanges. We match finishes across a full set so the rail line looks even from bow to stern.
Classic bronze hawse pipes, fairleads and chafe plates that guide lines and chain. Grooves worn by years of rope are smoothed before the new plating goes on.
Turnbuckle bodies, pad eyes, deck rings, bow eyes and cable clamps. We restore the finish and the look; structural parts should still be checked by a rigger.
Door latches, hinges, pulls, cabin lights, vents and small trim. The interior pieces that set the tone the moment someone steps aboard.
Slide the handle on each photo to compare a fitting the way it came off the boat and the way it went back on.
Before
Chrome lifting in flakes and green corrosion showing through. Stripped to bare bronze, pits filled with copper, then finished in bright nickel and chrome.
Before
Rust spots and cloudy chrome on the spokes and center hub. Each spoke was cleaned up, polished and plated again so the helm shines as a matched piece.
Before
Deep rope wear and dark corrosion around the opening. The grooves were smoothed and leveled with copper before nickel and chrome brought back a clean, even shine.
You don't have to live nearby to work with us.
Customers all over the country pack their parts and ship them to our Oceanside shop. We finish them, inspect them and send them back insured. It starts with a few photos.
Most marine hardware fails in one of three ways. Here is what each one looks like and what we do about it.
Boat hardware comes in more alloys than most people expect. Each one needs its own prep before it can take a lasting finish.
The traditional choice for cleats, hawse pipes and through hull fittings. Bronze takes copper, nickel and chrome beautifully once the corrosion is cleaned away.
Common on cabin hardware, lights and older trim. Brass polishes up well and plates evenly, making it one of the easiest metals to bring back.
Needs a nickel strike before chrome will hold. Some stainless only needs a good polish, and we will tell you when plating is not worth it.
Found on many older boats, especially trim, horns and light housings. Soft and porous, so it is filled with copper and leveled slowly by hand.
Older wheels, brackets and fittings are often steel. Rust is stripped away completely and the surface is built back up before the final chrome.
Aluminum needs special pretreatment and is reviewed part by part. Send a photo or the alloy name and we will confirm before you ship.
No guessing about what happens to your parts. Here are the five steps for boat hardware coming from Calimesa.
Take the hardware off the boat, snap a few photos and note where each piece goes.
We look at the metal and the damage, then send a written price and lead time within 24 business hours.
Once you have your quote number, wrap the parts, put a printed sheet in the box and ship by ground. From Calimesa it usually takes one day to reach us.
Old plating comes off, pits and grooves are filled and leveled, then copper, nickel and chrome go on.
Every piece is checked in daylight, wrapped on its own and shipped back insured, ready to bolt on.
A quick list of the boat and yacht hardware we restore and the finishes we offer.
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
We have been plating in Oceanside since 1989, close enough to the coast to see what salt air does to metal every day. Boat owners, captains and restorers trust us with fittings they cannot easily replace.
Send a photo of your hardware and receive a no obligation quote within 24 hours.
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Whether your boat is in San Diego, the Great Lakes or Florida, small fittings ship to us easily and return insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Our customers include boat owners, shipwrights, marinas and resorts. If you are in Calimesa with hardware to restore, you are in good company.
The same rail fittings, stanchion bases and cleat style hardware we restore for boats show up on bar rails, lounges and waterfront decks at casino resorts. Trusted by casino resorts across North County San Diego.
Original fittings for vintage runabouts and wooden boats, restored so the hardware matches the varnish and the history.
Rail fittings, cleats and helm hardware refinished so every piece on deck matches.
Working boats that see heavy use and daily salt spray, brought back to a clean look between seasons.
Dock cleats, signage hardware and clubhouse fixtures restored in batches with a consistent finish.
Shops rebuilding boats for clients send us the hardware so they can focus on the hull and the woodwork.
Marine hardware lives a hard life. A quick polish and a thin coat will not survive one season, so every piece gets the full treatment.
Old plating is removed down to bare metal, so no hidden corrosion is left behind to push the new finish off.
Copper levels the surface, nickel adds the corrosion barrier and chrome seals it with a hard, bright top layer.
Finished parts are checked under natural light, where every flaw shows, before they are approved to ship.
Cleats, rail fittings and hardware sets are tagged and returned together, so pairs and matching pieces stay matched.
A Few Minutes of Care Goes a Long Way
Restored hardware is tougher than the original finish, but it still needs basic care in conditions like dry heat and sun. Wash off salt, dust and grime gently, dry the metal and never scrub chrome with anything rough. A soft cloth does more good than a strong cleaner.
Avoid mixing cleaners. Mild soap and fresh water are enough for chrome and nickel, and strong chemicals can cloud the finish. If something stubborn will not come off, send a photo and ask us before you try a stronger product.
Pay attention to where hardware meets the deck. Water that sits under a cleat or a rail base is often what starts the trouble, so keep the bedding sealant in good shape. When you reinstall restored parts, use fresh sealant and stainless or bronze fasteners that suit the fitting.
If you see a small spot of rust or lifting chrome, catch it early. Send us a photo; sometimes one piece can be redone before the damage spreads to the rest of the set.
Small Hardware Travels Well, Big Pieces Need a Plan
Most boat hardware is compact and heavy for its size, which makes it a great fit for mail in service. A box of cleats, chocks and rail fittings packs tight, ships at a fair price and comes back the same way. Owners from both coasts and the lakes in between send us their fittings this way.
Long rails, bow pulpits, towers and big frames are another matter. We can talk about them, but the shipping and handling can cost more than the plating itself. For boats kept around San Diego, Orange County or Riverside County, the easiest path for larger items is to bring them to the shop.
If you are not sure where your parts fall, send photos with rough measurements. We will tell you honestly whether shipping makes sense before you spend anything.
Restored Marine Hardware Gallery
Cleats, chocks, hawse pipes, wheels and cabin hardware from boats and yachts, restored in our Oceanside shop.
You can be anywhere in the US. Here are the four steps for mailing boat hardware from Calimesa to our shop in Oceanside.
Email photos of each fitting and tell us the finish you want. We reply with a written price and lead time, usually the same business day. Please wait for your quote number before shipping.
Wrap each fitting separately so metal never rubs against metal. Heavy bronze pieces can scratch each other badly in transit, so use plenty of padding.
Bag fasteners with their fitting and mark pairs, port and starboard, or bow and stern. Insure the box for its real value and email us the tracking number.
When the work is done we send photos for your approval, then repack everything in fresh materials and ship it back insured.
Every piece of marine hardware is stripped, repaired, plated and inspected at our shop in North County San Diego, just inland from Oceanside Harbor.
Chrome and nickel restoration for boat and yacht hardware since 1989.
Calimesa sits at the edge of Riverside and San Bernardino counties, close to Yucaipa and Redlands. Boats from here are towed to nearby lakes, and dry heat and sun take a toll on bare chrome.
These nearby cities have their own boat and yacht parts pages.
Frequently Asked Questions
Here is a mix of service questions and a few for Calimesa owners. If we missed yours, tell us and we will answer it.
It can. Sun, dust and heat are hard on chrome even without water. Around Calimesa you also get dry heat and sun. Cleaning off dust before it bakes on and storing the boat covered helps, and we can restore what has already worn.
Yes. Bag and label each boat's parts separately, and list every piece and the finish you want on the sheet in the box. We track each group on its own, so nothing gets mixed up between boats, even if the box comes from Calimesa.
Bright chrome is the mirror shine most people picture on a cleat or rail. Satin chrome has a softer, lower glare finish. Polished nickel is a third choice with a slightly warmer tone. We can help you choose from photos.
Yes. Bronze takes copper, nickel and chrome well once the corrosion is cleaned away. It is the classic marine metal, and we restore bronze cleats, hawse pipes and fittings in bright chrome or polished nickel.
Wrap every piece separately so metal never rubs against metal. Heavy bronze can scratch badly in transit, so use plenty of padding, then fill empty space in the box. Bag fasteners with their fitting.
Not at all. Most of what comes through our door is home and business hardware: faucets, light fixtures, door handles, cabinet pulls, railings and decorative pieces. We also work for hotels, restaurants, boat owners and manufacturers.
Tell us what the part is, roughly how big it is, how many pieces you have and the finish you're after. If you know the metal, mention it. If not, that's fine. We can usually tell from the photos.
Every part is quoted on its own. The biggest factors are condition, the base metal, size and shape, the finish you choose and how many pieces you send. A part with deep pits or broken spots takes more work before it can be plated.