Show Chrome Restoration
Triple plated in copper, nickel and chrome and buffed by hand between layers, for the deep, wet shine that makes small trim stand out on a finished build.
From dash bezels to clutch levers, we strip, fill, level and plate the small pieces on your classic. Share a few photos and we will quote it in writing.
Restoring what was made to last in the first place
Decorative Metal Coatings has been restoring plated parts since 1989, and small classic car and motorcycle pieces are a big part of what comes through our shop in Oceanside. If you have a door handle, a bezel or a lever in Phoenix that has seen better days, we can strip it, repair it and plate it again.
Every part starts the same way. The old chrome or nickel comes off, any rust is cleaned out, and the surface is built back up and leveled by hand before new layers go on. That slow prep is the reason a restored part keeps its shine instead of flaking again.
The steps are the same whether your parts start in Phoenix, Tempe or Scottsdale. Shipping to us from Arizona is simple: get a quote, pack the parts, and we return them to you insured. In every case you get a written quote first, so there are no surprises when the parts come back.
Small parts are our sweet spot, and they are easy and affordable to ship from anywhere in the country. Send a few photos, tell us what the parts came from and how you want them to look, and we will send back a written quote.
We keep the menu simple: repair what is damaged, then plate it right. Below are the services that cover most of the small classic car and motorcycle parts we see.
Triple plated in copper, nickel and chrome and buffed by hand between layers, for the deep, wet shine that makes small trim stand out on a finished build.
Pitted and blistered pot metal is stripped, filled and leveled in copper before it is plated. Slow, careful work that saves parts most shops send back.
Bright or satin nickel for earlier cars and motorcycles that left the factory with a softer, warmer shine than modern chrome.
Knobs, handles, window cranks, bezels and switch plates restored so the inside of your classic matches the outside.
Levers, clamps, mirror stems, small covers and controls replated so a vintage bike looks right from every angle.
Original bolts, nuts, clips and small brackets cleaned and replated, so you keep correct factory hardware instead of buying generic replacements.
Drag the handle on any photo to see the part as it arrived and as it left our shop.
Before
Bubbled, flaking chrome over pitted pot metal. Stripped, filled in copper, leveled by hand and triple plated in show chrome.
Before
A thin steel ring with surface rust and worn plating. Stripped, polished and finished in bright nickel and chrome.
Before
A coffee can full of rusty original bolts, clips and small brackets. Cleaned, sorted and replated as a matching set, ready to go back on.
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
Owners, shops and collectors trust us with parts that are hard or impossible to replace.
Not every part needs the same treatment. Picking the right level for each piece keeps your budget where it matters most.
Classic parts were made from a handful of metals, and each one needs its own preparation before it can shine again.
Used for door handles, hood ornaments, interior knobs and many trim pieces. We stop the pitting, fill it in copper and level it by hand before plating.
Brackets, bezels, levers and hardware. Rust is removed down to clean metal, then the part is polished and plated in copper, nickel and chrome.
Common on early vehicles, lamps and fittings. Brass takes nickel and chrome beautifully once it has been cleaned and polished.
Some trim pieces and motorcycle covers are aluminum. They need a special pretreatment before plating, so we review each piece before quoting.
Many classic trim pieces are stainless and may only need polishing. If yours does need plating, it gets a nickel strike first so the finish bonds.
Older fittings and hardware in copper or bronze clean up well and plate easily, whether you want them chromed or nickeled.
There is nothing complicated about sending us a part. Follow these steps and we do the rest.
Photograph each part from a few angles and tell us what it came from and the finish you want.
We check the condition and the metal, then send a written quote and lead time within 24 business hours.
Ship the parts to us in a box just big enough for them and the padding. Add your quote number, a parts list and your phone number.
Old plating and rust come off, pits are filled, and the surface is leveled and polished by hand.
Copper, nickel and chrome go on in layers, then every part is inspected, packed and returned insured.
What Size Parts Make Sense to Ship
Most of the classic and vintage work that comes through our door fits in a small box. Handles, knobs, bezels, levers, brackets, hardware and short trim pieces are light, they pack easily and the shipping cost both ways stays reasonable. For owners outside California, these are the parts where mailing them to a specialty shop makes the most sense.
Larger pieces like bumpers, grilles and full length trim are a different story. We can plate them, but they need oversized boxes or freight, and the trip here and back can add up quickly. If you live in Southern California, the easiest option is simply to bring them to the shop.
If you are farther away and still want us to handle a large part, we are happy to take a look. Send photos and measurements, we will quote the plating, and you can weigh that against the shipping before you decide. No pressure either way.
A quick list of the classic and vintage parts and finishes we handle most often.
We have been restoring plated parts since 1989. Car owners, motorcycle restorers and private collectors send us the pieces they cannot replace, because we take the time to save them.
Send photos of your parts and get a no obligation quote within 24 hours.
Every restored part is backed by our craftsmanship guarantee. If something is not right, we make it right.
Small parts travel easily from any state and come back to you insured.
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
On a classic, people look closely. Every shortcut in stripping or prep shows up later as peeling, pits or haze, so we do the slow work first.
Old chrome and nickel are fully removed, so the new layers bond to clean metal instead of a finish that is already failing.
Copper is built up and leveled by hand until pits disappear, which is what separates a show finish from a quick rechrome.
Every part is checked for haze, pits and missed spots before it is approved to leave the shop.
Each restored part is wrapped on its own, so fresh chrome never rubs against another piece on the way home.
The people who send us parts are as varied as the parts themselves. Here are the groups we work with most, whether they are in Phoenix or far away.
Antique slot machine trim, handles and casino collectibles restored to their original shine. Casino resorts across North County San Diego trust us with their decorative metal work.
Private owners and restoration shops rebuilding American and European classics, one small part at a time.
Riders and builders bringing old bikes back to original condition, or giving a custom build a clean, bright finish.
Shops that need dependable show chrome on small parts, with clear quotes and consistent quality job after job.
Owners getting ready for shows and judging who need finishes that hold up under a very close look.
Collectors of automobilia and vintage hardware who want a treasured piece to look the way it did when it was new.
Protect the work once it comes home
Phoenix summers are brutally hot, and strong sun is hard on wax, so reapply protection more often than you would elsewhere. A quick wipe with a soft cloth after each drive keeps dust, moisture and road film from settling into the finish.
Waxing nickel is especially worthwhile, because it is softer than chrome and shows wear sooner if left bare. Take a photo of each restored part before it goes back on the vehicle, so you have a record of how it looked.
Skip steel wool, rubbing compound and harsh wheel cleaners. They scratch the surface and can cut through the chrome to the nickel underneath. If a spot needs more than soap, use a polish made for chrome and a soft cloth. Nickel is softer than chrome, so treat nickel parts gently and always dry them well.
For storage, keep parts and vehicles somewhere dry under a breathable cover, never plastic that traps moisture. If you notice small rust spots or lifting plating, send us a photo. Catching a problem early is always easier than waiting.
Restored Parts Gallery
Door handles, bezels, cranks, levers and original hardware from classic cars and vintage motorcycles, restored in our Oceanside shop.
Wrap, box, label and ship. These four steps keep your parts safe on the way to our Oceanside shop and back home again.
Send photos of every part and the finish you want. You will get a written quote and lead time, usually the same business day. Please wait for your quote number before you ship.
Wrap each part on its own so metal never touches metal, and use a box just large enough for the parts and padding. A snug box keeps parts safe and keeps the shipping cost down.
Bag and label small hardware by where it goes so sets come back together easily. Declare the real value with the carrier and email us the tracking number.
When your parts are finished we send photos for your approval, then pack them in fresh materials and ship them back insured.
Local car and motorcycle owners are welcome to drop off parts at our shop in North County San Diego. It is also the easiest option for larger pieces.
Chrome, nickel and copper restoration for classic and vintage parts since 1989.
If you cannot visit our shop in person, that is fine. Owners in Arizona can send photos, get a written quote, ship small parts and have them returned insured, all without leaving home.
Nearby cities have their own pages with details on classic parts restoration.
Frequently Asked Questions
Short, honest answers about restoring classic parts, whether you are in Phoenix or far from our shop.
Hand buffing between layers smooths each surface before the next one goes on, which gives the final chrome its depth. Machines can round edges and wash out detail on small parts. Doing it by hand takes longer, but the result is better.
For small parts, yes. Handles, bezels, levers and hardware are light and fit in small boxes, so shipping both ways stays reasonable. For large pieces, get a quote and compare plating with freight before you decide.
No, we can plate them. They need oversized boxes or freight, though, and shipping both ways can add up. Send photos and measurements for a quote, then compare the plating cost with the shipping before you decide.
In many cases yes, especially when reproductions do not exist or do not fit well. Restoring keeps the original detail and your car or bike stays correct. A photo quote will show you the real numbers, so you can compare.
Ask us first. Some parts have rubber, glass or other pieces that should not be plated. Send photos and tell us what the part is, and we will explain what to take off and what to leave alone.
Send us a few photos of the part from different angles, along with what it is and the finish you want. We look them over and send a written quote, usually within 24 business hours. It's free, and you're under no obligation to go ahead.
Standard orders take 3 to 5 weeks from the day your parts arrive. If you're on a deadline, ask about expedited service. When the schedule allows, we can finish in 5 to 7 business days.
Yes. Our workmanship is covered for 12 months. If something isn't right with the finish we put on, call us and we'll make it right.