Bright Copper
A deep, mirror polished copper finish for lighting, hardware and decorative pieces, sealed with a clear coat so the color stays rich instead of darkening.
Copper Plating in Flagstaff, AZ
Copper plating in Flagstaff for homes and cabins under the San Francisco Peaks, the shops and restaurants downtown and along Route 66 and the campus at Northern Arizona University. Pack your pieces for the trip to our Oceanside, California shop, where we prep, plate and seal them before insuring the box back up the mountain.
Certified, Approved and Verified
Why Flagstaff Customers Choose DMC
A mountain town at 7,000 feet, where Pluto was found.
Flagstaff sits at about 7,000 feet in the largest ponderosa pine forest in the country, under the San Francisco Peaks. Lowell Observatory, where Pluto was discovered, sits on a hill above downtown. Route 66 runs through town, and winters mean real snow, often lots of it.
Mountain parts need extra prep. They show up with road grime, deicer residue and water trapped under old lacquer from months of freeze and thaw. All of that has to come off, or the copper won't bond. We strip each piece, clean out every crevice, sand the pitting and buff it smooth before plating.
Flagstaff sends us cabin hardware, lanterns and fireplace pieces, signs from Route 66 businesses, fixtures from downtown restaurants and pieces from the university. Brick buildings downtown hold plenty of older hardware worth saving.
Tell us what the part is and what you want it to become. Send a few photos and the base metal if you know it, and we will recommend the right copper process, explain the preparation it needs and send back a written quote.
What We Do
Copper Plating Services
Flagstaff cabins usually get antique copper, which looks right next to pine and stone, and restaurants downtown choose bright copper for lights that glow on snowy nights.
Satin Copper
A brushed, low glare copper with a soft grain. It hides fingerprints and light wear, a favorite for door hardware, cabinet pulls and interior trim.
Antique Copper
Copper that is darkened and then relieved by hand, so the high points glow while recesses stay deep brown. Ideal for period restorations and rustic designs.
Copper Buff Base
A heavy acid copper layer that is cut and buffed flat before nickel and chrome. It fills pits and polishing marks and is the foundation of every show chrome job.
Copper Strike
A thin first layer that locks onto difficult metals like zinc die cast, steel and brass, giving every layer that follows a solid bond.
Industrial Copper
Functional copper for conductivity, solderability and heat treat masking. Plated to a specified thickness on bus bars, connectors, shafts and gears.
Restoration Results
Before and After
Drag the handle on any photo to see the part as it arrived and as it left the shop in copper.
Before
Vintage Table Lamp
Worn, spotted brass with decades of tarnish. Stripped, polished and plated in bright copper, then sealed with a clear lacquer so the warm color stays put.
BRIGHT COPPER
BRASS
LACQUERED
Before
Antique Door Hardware
A full set of levers, plates and hinges with peeling plating. Stripped, copper plated and hand antiqued so the raised details stand out against darker recesses.
ANTIQUE COPPER
STEEL
SET MATCH
Before
Copper Base for Chrome
Pitted metal with failed chrome. Stripped down, built up in heavy acid copper, then cut and buffed flat to create a perfect base for nickel and chrome.
COPPER BUFF BASE
STEEL
SHOW CHROME PREP
One Piece or a Thousand
Big order or a single knob, same care.
Homeowners send us one faucet. Companies in and out of state send production runs of hundreds or thousands of parts. Both get a written quote and the same inspection before anything ships back.
What We Can Finish
Metals We Copper Plate
Copper bonds to more base metals than almost any other plating, but each one still needs the right cleaning and the right first layer.
Steel
Cleaned and activated, then given a copper strike before the main copper layer. Rusted or pitted steel is stripped and copper filled until the surface is smooth.
Brass and Bronze
Plate beautifully once cleaned. A common way to give brass lighting, hardware and fixtures a true copper color without replacing the part.
Zinc Die Cast and Pot Metal
Porous and reactive, so it needs a gentle copper strike before anything else. Pits are copper filled and hand buffed flat, the slow work most shops avoid.
Aluminum
Receives a zincate pretreatment so copper can bond to a surface that would otherwise oxidize instantly. Used for wheels, housings and decorative castings.
Stainless Steel
Its oxide layer resists bonding, so it gets a nickel strike first. After that it takes copper like any other metal, for a warm look on a durable base.
Copper and Specialty Alloys
Solid copper can be replated to restore its surface, and other alloys are reviewed case by case. Send the alloy or a photo and we will confirm before you ship.
Choosing the Right Copper
Three Ways We Use Copper
The same metal, three different goals. Knowing which one your part needs decides how it is prepared, how thick the copper goes on and how it is finished.
Copper as the Finish
- Bright, satin or antique look
- Sealed with clear lacquer
- Lighting, hardware and decor
- Color matched to a sample
- Judged by appearance
Copper Under Chrome
- Heavy layer, buffed flat
- Fills pits and polishing marks
- Covered by nickel and chrome
- Bumpers, trim and wheels
- Judged by the final chrome
Functional Copper
- Conductivity and solderability
- Heat treat stop off masking
- Plated to a set thickness
- Bus bars, contacts, gears
- Judged by spec and coverage
How It Works
Our Copper Plating Process
These five steps carry your parts from the mountains to our bench and back.
1
Send Photos
Show us the part and tell us the finish you want: bright, satin, antique or a base for chrome.
2
Get Your Quote
We confirm the base metal and the prep it needs, then send a written quote within 24 business hours.
3
Ship or Drop Off
Dry everything fully first, since trapped snowmelt can spot copper in transit, then wrap and pack each piece. Ground shipping from Flagstaff usually takes 1 to 2 business days.
4
Strip, Strike and Plate
Old finishes come off, the surface is repaired and polished, then struck and plated in copper.
5
Finish and Seal
Parts are buffed, brushed or antiqued, sealed when needed, inspected and shipped back insured.
Copper Plating Catalog
Copper Finishes and Services
Every copper finish and copper related service we run in house.
Decorative Copper
- Bright Copper
- Polished Copper
- Satin Copper
- Brushed Copper
- Antique Copper
- Oil Rubbed Copper
- Clear Lacquer Topcoat
Underlayer and Industrial
- Copper Buff Base for Chrome
- Acid Copper Leveling Layer
- Copper Strike
- Conductive Copper
- Copper for Soldering
- Heat Treat Stop Off Copper
Base Metals and Prep
- Steel
- Stainless Steel
- Brass and Bronze
- Zinc Die Cast
- Aluminum (Zincate)
- Stripping and Replating
- Masking for Selective Plating
- Custom Sample Match
What Our Clients Say
Trusted by Professionals
From custom builders to industrial manufacturers, our clients trust us to deliver the same result every time.
Who We Serve
Who Relies on Our Copper
We plate for Flagstaff homeowners, cabin owners, the university, downtown restaurants and shops and businesses along Route 66.
Casinos and Gaming
Slot machine trim, table rails, bar fixtures and gaming floor accents in bright or antique copper, made to glow under bright lights around the clock. Trusted by casino resorts across North County San Diego.
Lighting and Decor
Pendants, sconces, lamp bases and accessories finished in bright, satin or antique copper.
Architectural Hardware
Door handles, hinges, cabinet pulls and railings given a warm copper finish that matches across a project.
Hospitality
Bar rails, foot rests, tap handles and restaurant fixtures that bring copper warmth to a space.
Electrical Components
Bus bars, terminals and connectors plated for conductivity and easy soldering.
Manufacturing and Heat Treat
Gears, shafts and steel parts selectively copper plated to mask areas during carburizing.
35+
Years of Expertise
Take a Moment to Learn More
About Decorative Metal Coatings
We have been running copper tanks since 1989. Restorers, designers, builders and manufacturers send us parts because the copper work underneath is what makes the finish on top last.
Free Estimates Available
Send a photo of your part and receive a no obligation quote within 24 hours.
Quality Guaranteed
Every part leaves our shop backed by our craftsmanship guarantee. If you are not satisfied, we make it right.
Ship From Anywhere in the US
A single fixture or a full production run, shipped to us from any state and returned insured.
Fast Turnaround Times
Most projects are completed within 3 to 5 weeks. Expedited Orders: 5 to 7 business days. Contact us for availability.
Our Commitment
Copper Done the Right Way
Copper shows everything. Every scratch left in the base metal and every shortcut in the prep ends up visible in the finish, so we do not take shortcuts.
Proper Strike Layer
Difficult metals get the right first layer before the main copper goes on, so the finish stays bonded and does not peel or blister.
Hand Buffed
Copper is cut and buffed by hand between stages, which is what gives decorative copper its depth and chrome its flawless base.
Color Checked
Finished copper is inspected for even color, gloss and texture, and matched to your sample when you send one.
Packed to Protect
Soft copper scratches easily, so every finished piece is wrapped separately and packed to arrive exactly as it left the shop.
What We Do Differently
- We confirm the base metal before choosing the copper process
- Old plating is stripped instead of covered over
- Decorative copper is sealed so the color lasts
- We send photos when a part needs a decision from you
- Every order is inspected before it is packed
What You May Experience Elsewhere
- Copper plated straight over old, failing finishes
- No strike layer, leading to peeling and blistering
- Unsealed copper that turns brown within weeks
- Polishing marks left visible under the finish
- Little communication once parts are in the shop
Copper Care Tips for Flagstaff
Snow, sun and freeze and thaw. Brush, dry, repeat.
Flagstaff snow melts in the afternoon sun and freezes again at night. Each cycle pushes water into scratches in lacquer. Brush snow off outdoor copper gently with a soft broom, and wipe it dry once the sun comes out.
Pine sap and soot are the other two Flagstaff problems. Loosen sap with warm soapy water and a soft cloth instead of scraping, then rinse and dry. Near the fireplace, wipe copper weekly so soot doesn't hold moisture against it.
If you prefer a living finish, we can leave the copper unsealed so it develops its own patina over time. That choice works well on rustic lighting, garden pieces and bar tops where the aging is part of the character.
When a lacquered piece starts to show dark spots, the coating has failed somewhere. Bring it back and we can strip the old lacquer, rebuff the copper and seal it again, usually without replating the whole part.
Project Gallery
Copper Plating Gallery
Bright, satin and antique copper on lighting, hardware and hospitality pieces, plus functional copper for electrical and industrial work.
Nationwide Service
Ship Us Your Parts From Anywhere in the US
Parcels from the high country usually take 1 to 2 business days to reach Oceanside.
01
Quote before you ship
Send photos of every piece and the copper finish you want. You receive a written quote and lead time, usually the same business day. Always wait for a quote number before shipping.
02
Wrap every piece on its own
Wrap each part individually so metal never touches metal, and use at least three inches of padding on every side. Long trim and lighting arms should be double boxed.
03
Insure it and share tracking
Declare the real value with the carrier and email us the tracking number so we can log your parts the day they arrive.
04
Inspected, then shipped back
When the copper work is done we photograph the finished pieces for your approval, then pack them in fresh materials and ship them back insured.
Visit Us
Our Location
Every copper job is stripped, plated, buffed and inspected in our own facility in North County San Diego.
Decorative Metal Coatings
Copper, nickel, chrome and metal finishing in San Diego County since 1989.
- Address 2613 Temple Heights Dr, Ste G, Oceanside, CA 92056
- Phone (760) 746 3378
- Quotes Send photos and get a price
Business Hours
- Monday to Friday 8:00 AM to 5:00 PM
- Saturday 9:00 AM to 2:00 PM
- Sunday Closed
Shipping from Flagstaff
Winter storms on Interstate 40 can slow trucks out of Flagstaff. Plan copper projects for spring or fall when you can, and keep your tracking number. Our shop is in Oceanside, California, and returns are insured.
Nearby Cities We Serve
Down the mountain and across northern Arizona, these cities send copper too.
Copper Plating Questions from Flagstaff
Frequently Asked Questions
Flagstaff cabin owners and business owners ask us these five questions most.
Yes. Door sets, hinges, lanterns and fireplace tools from mountain cabins plate well in copper once old finishes and grime are stripped. Antique copper looks natural next to pine and stone. A clear coat helps with snow and freeze and thaw.
It can wear lacquer faster, since melting snow seeps into scratches and refreezes. The copper itself handles cold fine. Brush snow off gently, wipe fixtures dry and check outdoor pieces each spring for cracked or cloudy lacquer.
Months of snow, road grime and deicer leave residue in every crevice and under old lacquer. If any of it stays, the new copper won't bond and can peel. We strip and clean thoroughly before plating, which takes time but makes the finish last.
Yes, if they're metal and come down in one piece. Letters, plaques and emblems plate nicely in bright or antique copper. We seal them for mountain weather. Send photos and measurements first so we can check sizes.
Handles, hooks, screen frames and decorative trim can be plated if they come apart. Soot and heat are tough on copper, so we suggest antique copper with lacquer. Keep plated pieces away from direct flame.
The shop is open Monday to Friday from 8 AM to 5 PM and Saturday from 9 AM to 2 PM. We're closed on Sunday. Shipments are received Monday to Friday, 8 AM to 4 PM Pacific.
Usually, yes. Send a photo of the piece you want to match, or ship it along with your parts as a sample. We adjust the finish until the new work sits right next to the old.
When the work is done and inspected, we pack your parts in fresh materials and ship them back insured. If you're close to Oceanside, you're welcome to pick them up instead.